220-1201 Exam Dumps - CompTIA A+ Core 1 Exam (2025)

RG11 coaxial cable with quad shielding is designed to handle large volumes of internet traffic, providing excellent resistance to interference and high bandwidth capacity.

Why Not A (USB 3.1): USB 3.1 is used for connecting peripherals, not for high-volume internet traffic.

Why Not C (SATA3.0): SATA is used for internal data storage connections, not for network traffic.

Why Not D (Unshielded plenum RJ45): While RJ45 cables are commonly used, unshielded cables are prone to interference and are not ideal for high-volume traffic.

CompTIA A+ Exam Reference: Core 1 (220-1201), Section 3.1, cable types and their characteristics​.

A sandbox in virtualization allows testing an application in an isolated environment to observe its behavior without affecting the host system.

Why Not A (Run an application on multiple workstations): This describes application virtualization, not sandboxing.

Why Not C (Migrate a legacy application): This is about virtualization for legacy support, not testing.

Why Not D (Create a firewall): A firewall does not act as a sandbox for application testing.

CompTIA A+ Exam Reference: Core 1 (220-1201), Section 4.2, virtualization and sandboxing​.

To locate or identify an unlabeled network connection, the tool most suited for tracing cables through walls, ceilings, or patch panels is a toner probe (also called a tone generator and probe kit). CompTIA A+ describes this tool as essential for cable identification: the technician attaches the tone generator to one end of the network cable, and the probe detects the signal on the other end, even across long distances or through bundled wiring.

This makes the toner probe ideal for environments where cables are unlabeled, routed through structured cabling systems, or mixed with other wires. It allows the technician to listen for the distinctive tone, confirming the cable’s termination point.

A cable tester (C) verifies wiring integrity and pinouts but cannot trace a cable through physical pathways. It is used after identification, not during it. A loopback plug (B) is used for port testing and NIC diagnostics, not cable tracing. A network tap (A) is used for traffic monitoring, security analysis, and packet capture; it does not help locate cables.

Therefore, the toner probe is the correct tool for identifying and tracing an unlabeled network cable, aligning with CompTIA’s recommended cable management and troubleshooting procedures.

Abulging tablet casingis a classic sign of aswollen lithium-ion battery, often caused by age, overheating, or overcharging. This is adangerous condition, as swollen batteries can rupture or catch fire. It also explains why the tablet only works when plugged in the battery is no longer holding a charge.

Option A:Power supply issues wouldn’t cause physical bulging.

Option B:A bad charge port wouldn’t cause screen damage or physical distortion.

Option D:A broken screen could cause display issues, but not the bulging chassis.

CompTIA A+ Core 1 Exam Objective Reference:

Objective 1.4: Given a scenario, configure settings and use cases for laptops and mobile devices.

===========

CompTIA A+ teaches that S.M.A.R.T. warnings indicate imminent drive failure. Even if the RAID controller reports the array as “healthy,” a S.M.A.R.T. alert means the drive should be replaced immediately.

RAID 5 provides redundancy for one drive failure, but technicians should replace the degrading drive before it fails fully, ensuring the rebuild happens proactively.

Running chkdsk affects file systems, not drive health. Disabling write caching is unrelated. Rebuilding the array should only occur after replacing the faulty drive.

Replacing the drive prevents a catastrophic dual-drive failure scenario, which RAID 5 cannot survive.

This approach aligns with CompTIA troubleshooting guidelines for RAID maintenance and S.M.A.R.T. diagnostics.

If the user is on a guest network and cannot access internal resources like printers, connecting to the corporate Wi-Fi will place the device on the correct subnet to access the printer.

From CompTIA A+ 220-1101 Official Study Guide, Objective 2.2 – Network segmentation:

“Guest networks are isolated from internal resources for security. Connect to the main corporate Wi-Fi to access shared devices.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 2: Wireless Networking

CompTIA Exam Objectives 220-1101, Domain 2.2

============

A hypervisor is software or firmware that allows multiple operating systems (virtual machines) to run on a single physical host. It manages the allocation of resources and isolation of each VM.

From CompTIA A+ 220-1101 Official Study Guide, Objective 3.7 – Virtualization concepts:

“A hypervisor is the key component of virtualization, enabling a physical server to host multiple virtual machines (VMs), each with its own OS and resources.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 3: Virtualization

CompTIA Exam Objectives 220-1101, Domain 3.7

============

Virtual Desktop Infrastructure (VDI) hosts user desktops on centralized servers rather than physical PCs. Users access a virtual desktop session remotely through thin clients, laptops, or web browsers. The CompTIA A+ cloud-computing domain explains that VDI improves manageability, security, and resource efficiency by allowing IT to centralize OS images, apps, and updates.

SaaS provides applications not desktops. RMM is for monitoring and managing devices. Containers virtualize applications, not full desktops.

VDI enables organizations to avoid purchasing physical desktops while still delivering full computing environments to users, which aligns with the A+ virtualization objectives and remote-access concepts.