220-1201 Exam Dumps - CompTIA A+ Core 1 Exam (2026)

A computer tower with a hard drive and a hard drive AI-generated content may be incorrect.

A computer tower with a computer and a hard drive AI-generated content may be incorrect.

Modern motherboards require both the 24-pin ATX connector and a 4-pin or 8-pin CPU power connector. If the CPU power connector is not attached, the motherboard will receive power but the system will not boot. CompTIA A+ specifically lists this as a common mistake after replacing a power supply.

Insufficient wattage may cause instability, but usually the system still attempts to start. RAM does not prevent power-on if missing; instead, the system produces beep codes. Redundant PSUs are used in servers, not standard desktops.

Therefore, the missing CPU power connector is the most likely cause, and this scenario reflects typical troubleshooting steps outlined in A+ hardware diagnostics.

Wireless coverage issues at the physical edges of a building are typically caused by weak RF signal strength. The CompTIA A+ study material says the best solution is to add additional wireless access points (APs) or implement a mesh system to extend coverage and eliminate dead zones.

Enabling 5GHz often worsens the issue because 5GHz has shorter range. Wi-Fi 6 NIC upgrades improve performance but do not increase signal reach. Flushing DNS does not affect wireless coverage.

Installing more APs ensures stronger coverage, better signal-to-noise ratio, and stable connectivity aligning with CompTIA’s wireless troubleshooting best practices.

An IP address beginning with 169.254.x.x is an APIPA address (Automatic Private IP Addressing). CompTIA A+ explains that APIPA is assigned automatically by Windows when the NIC cannot reach a DHCP server. This indicates the laptop requested an IP lease but never received one.

APIPA addresses allow only local subnet communication and cannot access the internet, because no default gateway, DNS, or valid subnet configuration is provided. Since all other employees can access the internet, the DHCP server is functioning generally, but it is not delivering an address to this specific laptop—possibly due to cable issues, Wi-Fi authentication failure, DHCP scope exhaustion, or NIC misconfiguration.

A subnet mask misconfiguration (A) would still show a normal IP, not APIPA. IPv6-only configuration (C) would not produce a 169.254 address. An outdated NIC driver (B) could cause network instability but does not directly generate APIPA.

Thus, the root cause is that the DHCP server did not assign an IP address.

Whenever a CPU heat sink is removed or replaced, thermal paste must be reapplied. Thermal paste fills microscopic gaps between the CPU heat spreader and the heat sink, ensuring efficient heat transfer. Without it, there is a significant air gap, which acts as an insulator, causing CPU temperatures to rise dramatically even under light load. CompTIA A+ stresses thermal compound application as a key step in CPU cooling installation.

The scenario indicates that temperatures increased drastically after upgrading to a better heat sink. A higher-performing heat sink should improve temperatures, not worsen them—unless a critical installation step was missed. Missing thermal paste is the most common cause of this symptom and easily explains the sudden overheating.

Decreased CPU voltage would lower temperatures, not raise them. Higher fan RPM increases cooling efficiency, not reduces it. Airflow interruption is possible but less likely in a simple heat sink upgrade scenario unless the technician installed the CPU cooler incorrectly; however, the most direct and common cause described by CompTIA is missing thermal paste.

Thus, D is the correct answer.

Reasoning: A cable tester capable of testing Power over Ethernet (PoE) functionality can verify whether the switchport is providing the required power to the phone. This tool measures both the presence of data and the voltage or wattage being provided through the Ethernet cable.

This is the most effective way to confirm that PoE is available on the port.

Why the Other Options Are Incorrect:

A. Network tap:

A network tap is primarily used to monitor network traffic, not to test for PoE availability. It cannot verify if power is being supplied through the Ethernet cable.

C. Loopback plug:

A loopback plug is used to test the functionality of a network port by creating a loop for transmitted and received signals. It does not measure or verify PoE availability.

D. Toner probe:

A toner probe is used for tracing and identifying network cables. It cannot test for PoE functionality.

Practical Example:

A PoE phone might not turn on due to a misconfigured or faulty switchport. Using a cable tester capable of measuring PoE would help the technician determine if the switchport is supplying sufficient power to the phone.

CompTIA A+ Exam Objective Alignment:

Objective 2.1: Identify common networking hardware and tools, including PoE-enabled devices and cable testers.

B. PAN (Personal Area Network):

A PAN is a network established between devices in close proximity, such as between a smartphone and a Bluetooth headset.

Bluetooth technology is specifically designed for short-range communication, making it a type of PAN.

Incorrect Options:

A. MAN (Metropolitan Area Network): A MAN covers a city or metropolitan area and is not relevant to Bluetooth connections.

C. SAN (Storage Area Network): A SAN is used for large-scale data storage, unrelated to Bluetooth connections.

D. WAN (Wide Area Network): A WAN spans large geographical areas (e.g., the internet) and is not relevant to this scenario.

Key Takeaway: Bluetooth connections, such as those between a headset and a device, create a Personal Area Network (PAN).

An internal cloud platform operated exclusively for a single organization is a private cloud, providing dedicated resources and enhanced control.

From CompTIA A+ 220-1101 Official Study Guide, Objective 3.7 – Cloud models:

“A private cloud is provisioned for exclusive use by a single organization, typically managed internally or by a third party, and may be hosted on-premises.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 3: Cloud Concepts

CompTIA Exam Objectives 220-1101, Domain 3.7

============