220-1201 Exam Dumps - CompTIA A+ Core 1 Exam (2026)

A hard disk drive (HDD), especially if it ' s older or nearly full, is the most common cause of slow startup times in laptops. HDDs are much slower than SSDs and can significantly bottleneck the boot process.

From CompTIA A+ 220-1101 Official Study Guide, Objective 4.1 – Troubleshoot common hardware problems:

“A slow startup or sluggish system performance is commonly due to a failing or fragmented hard disk drive (HDD). Replacing with an SSD can greatly improve boot times and overall system responsiveness.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 4: Troubleshooting PC Hardware

CompTIA Exam Objectives 220-1101, Domain 4.1

============

Degraded performance that occurs only during business hours strongly suggests network congestion caused by simultaneous data and voice traffic. According to CompTIA Core 1 (220-1201) networking objectives, combining voice (VoIP) and data traffic on the same network without proper segmentation can lead to latency, jitter, and packet loss, especially during peak usage periods.

Implementing VLANs (Virtual Local Area Networks) allows administrators to logically separate voice and data traffic, enabling better traffic management and prioritization. VLANs also support Quality of Service (QoS) policies that ensure time-sensitive voice traffic is prioritized over standard data traffic, improving call quality and overall performance.

Replacing switches with higher-capacity models is costly and unnecessary if proper traffic segmentation has not yet been implemented. Adding RAM to PCs or VoIP lines does not address network-level congestion. Firmware updates may improve stability but will not resolve sustained performance degradation caused by traffic contention.

CompTIA highlights VLAN implementation as a best practice for environments that use IP phones, especially when performance issues occur during high utilization periods.

The best answer provided is A , although it is important to note that the question is somewhat misleading because it asks about motherboard selection but provides mostly incorrect or irrelevant motherboard-related options.

For high-performance workloads such as video editing and virtual reality (VR) using an Intel Core i9 processor and multiple graphics cards (multi-GPU setup) , system design considerations include high power consumption and significant heat output. In the CompTIA A+ Core 1 220-1201 objectives under hardware planning and troubleshooting, high-performance CPUs and multiple GPUs require adequate thermal management solutions , including advanced cooling systems (air or liquid cooling) to ensure system stability and prevent thermal throttling.

Why A is the best answer:

High-end CPUs like Intel Core i9 and multiple GPUs generate substantial heat.

Proper cooling is essential for maintaining performance under sustained load (video rendering, VR workloads).

While not strictly a motherboard feature, cooling is a critical system requirement for such a build.

Why the other options are incorrect:

B. Use DDR3 RAM for increased compatibility

Incorrect because modern Intel Core i9 platforms use DDR4 or DDR5 , not DDR3, which is obsolete and incompatible with current high-performance motherboards.

C. Verify there are two PCIe x1 slots for additional devices

Incorrect because PCIe x1 slots are used for low-bandwidth devices (sound cards, network cards), not graphics cards.

Multiple GPUs require PCIe x16 slots , not x1.

D. Select a motherboard with integrated graphics to support video output

Incorrect because high-performance systems with discrete GPUs rely on those GPUs for rendering. Integrated graphics are unnecessary and sometimes disabled when a dedicated GPU is installed.

Exam Insight (CompTIA A+ perspective):

In real-world A+ Core 1 scenarios, the correct motherboard selection for this requirement would focus on:

Multiple PCIe x16 slots (for multi-GPU support)

Compatible socket for Intel Core i9

Support for modern RAM (DDR4/DDR5)

Adequate chipset and power delivery (VRM design)

Proper cooling solution for thermal management

However, since those correct motherboard specifications are not provided in the options, A is the only viable system-level requirement relevant to stability under high-performance load .

The correct answer is C. DHCP (Dynamic Host Configuration Protocol) .

According to CompTIA A+ Core 1 220-1201 objectives under Networking:

DHCP is used to automatically assign IP addresses and related network configuration (such as subnet mask, default gateway, and DNS servers) to devices on a network.

This eliminates the need for manually configuring IP addresses on each PC and helps prevent conflicts.

Why the other options are incorrect:

A. VLAN (Virtual Local Area Network): VLANs segment a network into logical subnets but do not assign IP addresses.

B. DNS (Domain Name System): DNS translates domain names to IP addresses; it does not assign IP addresses to devices.

D. TCP (Transmission Control Protocol): TCP is a transport layer protocol used for reliable communication between devices, not for IP assignment.

User authentication allows access to device functions (like printing and copying) to be restricted to authorized personnel. This is typically implemented on networked multifunction devices for security and auditing.

From CompTIA A+ 220-1101 Official Study Guide, Objective 3.4 – Printer and device security:

“Enable user authentication on shared multifunction devices to restrict access to specific features for authorized users only.”

Verified Source:

CompTIA A+ Core 1 (220-1101) Official Study Guide, Chapter 3: Printer Security

CompTIA Exam Objectives 220-1101, Domain 3.4

The correct answer is D. DVI (Digital Visual Interface) .

According to CompTIA A+ Core 1 220-1201 objectives under Hardware and Display Technologies:

DVI is primarily a video-only interface that transmits digital or analog video signals from a source (like a computer) to a display.

Unlike HDMI or USB-C, DVI does not carry audio signals , making it strictly for video.

Why the other options are incorrect:

A. DisplayPort: Supports video and audio as well as other features such as daisy-chaining multiple monitors.

B. HDMI: Transmits both video and audio signals over a single cable.

C. USB-C: Can carry data, power, and video/audio signals depending on the device and protocol (e.g., DisplayPort Alt Mode).

solution as

A screenshot of a network settings AI-generated content may be incorrect.

A screenshot of a computer AI-generated content may be incorrect.

A screenshot of a computer AI-generated content may be incorrect.

The correct answer is D. Channel width .

According to CompTIA A+ Core 1 220-1201 objectives under Networking and Wireless:

Channel width refers to the size of the frequency band used for Wi-Fi communication.

Increasing channel width (e.g., from 20 MHz to 40 MHz, 80 MHz, or 160 MHz) allows more data to be transmitted at once, effectively increasing wireless throughput speed.

Why the other options are incorrect:

A. Licensed bands: Licensed spectrum is used for certain types of communication and does not directly increase Wi-Fi throughput.

B. Maximum transmission unit (MTU): MTU defines the largest packet size transmitted over a network but is not the primary factor for increasing Wi-Fi throughput.

C. Transmit power: Adjusting transmit power affects signal range and coverage but does not significantly increase throughput; it may improve connectivity but not data rates.