220-1201 Exam Dumps - CompTIA A+ Core 1 Exam (2026)

In Wi-Fi, the 2.4GHz band contains 14 total channels (depending on region), but only channels 1, 6, and 11 are considered non-overlapping in most countries. CompTIA A+ highlights the importance of selecting these channels to minimize interference, especially in environments with multiple wireless networks or access points.

The 2.4GHz band is narrower than 5GHz, causing adjacent channels to overlap significantly. Using channels 1, 6, and 11 prevents overlap and reduces signal interference, improving performance and stability.

5GHz (B) has many non-overlapping channels and does not use the 1/6/11 scheme. The 6GHz band (C) is part of Wi-Fi 6E and uses entirely different channel planning. The 60GHz band (D) supports short-range high-speed connections like WiGig, not traditional Wi-Fi channels.

Therefore, the 2.4GHz band is the correct answer.

The correct answer is D. WLAN (Wireless Local Area Network).

According to CompTIA A+ Core 1 220-1201 objectives under Networking:

A WLAN is a wireless network that covers a limited area such as an office, building, or campus.

Using a heat map helps administrators determine optimal placement of access points, identify areas of weak signal, and plan coverage for employees’ devices.

Why the other options are incorrect:

A. SAN (Storage Area Network): Connects storage devices over a network; not used for wireless coverage.

B. PAN (Personal Area Network): Covers a very small area, such as a single person’s devices (Bluetooth, USB, etc.), not a whole office.

C. MAN (Metropolitan Area Network): Covers a city or large geographic area; too large for a floor plan.

Comprehensive and Detailed Explanation From Exact Extract (Aligned With CompTIA A+ 220-1201 Study Guide)

When installing an operating system from external media (USB flash drive), the motherboard firmware must be instructed to check that device before checking the internal storage.

The CompTIA A+ official objectives describe that technicians must know how to access UEFI/BIOS settings and configure boot priority. Installing an OS from USB requires:

Entering UEFI/BIOS setup

Navigating to the Boot or Startup menu

Setting the USB drive as the first boot device

Saving and exiting to allow the computer to boot from the USB installer

This process is specifically referenced in CompTIA A+ material under “BIOS/UEFI settings,” where boot sequence / boot order is a fundamental configuration needed for OS installation.

Thus, the next step after assembling the PC is to modify the boot order to allow the system to boot from the USB installation media.

Why the other options are incorrect

A. BIOS password

Used for system access security; has no relevance to installing an OS from USB.

B. PXE boot

Used for network-based installations, not USB installations.

C. Secure Boot

Controls OS signature validation; not required to be changed for USB installation and is not the next required step.

Final Answer: D

The most likely cause of this issue is incorrect tray settings on the user’s printer. According to CompTIA Core 1 (220-1201) printer configuration and troubleshooting concepts, printers rely on tray configuration settings to determine the paper size and paper type loaded in each tray. If the tray is not configured for 11 × 17 (Tabloid/Ledger) paper, the printer will assume the required paper is unavailable—even if the paper is physically present.

When a print job specifies a paper size that does not match the tray’s configured settings, the printer commonly displays a message prompting the user to insert the correct paper. The fact that the same document prints successfully on another printer of the same model confirms that the driver, permissions, and connectivity are functioning correctly, further isolating the issue to the local printer’s tray configuration.

An incorrect driver would cause consistent problems across printers, not just one. Connectivity issues would prevent communication with the printer entirely, and insufficient permissions would generate access or authorization errors rather than a paper prompt.

CompTIA emphasizes verifying tray assignments and paper size configuration as a primary troubleshooting step when printers incorrectly request paper that is already loaded.

DHCP (Dynamic Host Configuration Protocol) is the service used to automatically assign IP addresses to network hosts. It dynamically manages the distribution of IP addresses and configuration details (like subnet mask, gateway, and DNS servers), ensuring no two devices are assigned the same address on the network.

Option B (DNS): Incorrect. DNS translates domain names into IP addresses but does not assign them.

Option C (LDAP): Incorrect. LDAP is a protocol used for accessing and maintaining directory services, such as user information and permissions.

Option D (SMTP): Incorrect. SMTP is used for sending and receiving email, not for IP address assignment.

The technician should replace the Ethernet cable because the problem is isolated to the laptop’s wired connection. The laptop connects reliably through Wi-Fi, which demonstrates that the internet service, router routing functions, operating system, and general network configuration are operational. An Ethernet cable with damaged conductors, loose connectors, poor termination, or intermittent internal breaks can cause the link to repeatedly disconnect or renegotiate. Replacing the cable with a known-good cable is a quick and inexpensive isolation step. Restarting the router is less appropriate because wireless connectivity through the same router works correctly. Disabling the firewall would unnecessarily weaken security and would not normally correct intermittent physical-link failures. Installing another wireless access point is irrelevant because Wi-Fi already functions without the reported problem. If replacing the cable does not resolve the issue, the router port and laptop Ethernet adapter should then be tested.

In CompTIA A+ Core 1 (220-1201) cloud concepts, the key differentiator between cloud deployment models is where the service is hosted and who owns/uses the underlying infrastructure. If a company’s directory services server (for example, a domain controller providing authentication/authorization and centralized identity management) is located on premises, that points to infrastructure that is owned and operated by the organization for its own internal use. This aligns best with a private cloud model, which is defined as cloud resources dedicated to a single organization and can be implemented on-premises (internally hosted) or in a dedicated off-site environment.

It is not a public cloud because public cloud services are hosted by a third-party provider and shared across multiple customers. It is not hybrid cloud because hybrid requires a mix of on-prem resources and public cloud resources working together (the question only specifies on-prem). It is not community cloud because that involves shared infrastructure among multiple organizations with common needs.

The degraded status on Server 2 indicates a RAID-5 issue, typically due to a failed or failing drive. In RAID-5 configurations, when one drive fails, the system can still operate but with reduced performance as parity data is used to rebuild missing data on-the-fly.

Recommended Replacement Drive:

To minimize performance degradation, the replacement drive should be:

SAS HDD with the same specifications (64KB stripe size, no read-ahead, and write-back policy).

Matching the configuration exactly ensures seamless integration and optimizes recovery speed in the RAID-5 array.

In RAID-5, degraded performance is expected when one drive fails, as parity data needs to rebuild missing information during each read/write process. Replacing the failed drive restores the RAID array to optimal status, reducing the load on existing drives and returning the system to normal read/write performance. The write-back policy and disabled disk cache settings are designed to reduce latency and increase efficiency, essential for handling real-time applications.

A user reports poor performance on the

application server.

INSTRUCTIONS

Click on Server 1 and Server 2 and review

the information presented in each chart to

determine which drives need to be replaced.

Select the appropriate replacement drive

that should be used, for the least

performance degradation to the server.

A computer server with many black and silver parts AI-generated content may be incorrect.A computer server with many black boxes Description automatically generated with medium confidence

A screen shot of a computer AI-generated content may be incorrect.A screen shot of a computer Description automatically generated

A computer screen shot of a computer AI-generated content may be incorrect.A computer screen shot of a computer Description automatically generated

A computer screen shot of a computer AI-generated content may be incorrect.A computer screen shot of a computer Description automatically generated

A computer screen shot of a computer AI-generated content may be incorrect.A computer screen shot of a computer Description automatically generated

A screenshot of a computer AI-generated content may be incorrect.A screenshot of a computer Description automatically generated

A screenshot of a computer AI-generated content may be incorrect.A screenshot of a computer Description automatically generated