300-410 Exam Dumps - Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)

Searching for workable clues to ace the Cisco 300-410 Exam? You’re on the right place! ExamCert has realistic, trusted and authentic exam prep tools to help you achieve your desired credential. ExamCert’s 300-410 PDF Study Guide, Testing Engine and Exam Dumps follow a reliable exam preparation strategy, providing you the most relevant and updated study material that is crafted in an easy to learn format of questions and answers. ExamCert’s study tools aim at simplifying all complex and confusing concepts of the exam and introduce you to the real exam scenario and practice it with the help of its testing engine and real exam dumps

Go to page:

<< First
Prev
4
5
6
7
8
9
10
11
12
13
Next
Last >>

Question # 65

A network administrator successfully established a DMVPN tunnel with one hub and two spokes using EIGRP. One of the requirements was to enable spoke-to-spoke tunnels through the hub router using EIGRP. Which configuration command must the engineer configure to meet the requirement?

no ip eigrp 1 mode multipoint

no ip eigrp 1 split-horizon

no ip eigrp 1 tunnel-redirect

no ip eigrp 1 mode mgre

Full Access

Question # 66

Refer to the exhibit The engineer configured route redistribution in the network but soon received reports that R2 cannot access 192 168 7 0/24 and 192 168 15 0/24 subnets Which configuration resolves the issue?

Option A

Option B

Option C

Option D

Full Access

Question # 67

How is a preshared key " Testâ€™â€™ for all the remote VPN rooters configured In a DMVPN using GRE over IPsec set up?

authentication pre-share Test address 0.0.0.0 0.0.0.0

set pre-share Test address 0.0.0.0 0.0.0.0

crypto Ipsec key Test address 0.0.0.0 0.0.0.0

crypto isakmp key Test address 0.0.0.0 0.0.0.0

Full Access

Question # 68

Which IPv6 first hop security feature controls the traffic necessary for proper discovery of neighbor device operation and performance?

RA Throttling

Source or Destination Guard

ND Multicast Suppression

IPv6 Snooping

Full Access

Question # 69

Refer to the exhibit. An engineer implemented an access list on R1 to allow anyone to Telnet except R2 Loopback0 to R1 Loopback4 How must sequence 20 be replaced on the R1 access list to resolve the issue?

sequence 20 permit tcp host 1001 ABC:2011:7:: 1 host 400A:0:400C::1 eq telnet

sequence 20 deny tcp host 400A:0:400C::1 host 1001 :ABC:2011:7::1 eq telnet

sequence 20 deny tcp host 1001:ABC:2011:7::1 host 400A:0:400C::1 eq telnet

sequence 20 permit tcp host 400A:0:400C::1 host 1001ABC:2011:7::1 eq telnet

Full Access

Question # 70

Refer to the exhibit. The users from subnet 172.16.1.16/28 are experiencing connectivity issues to subnet 172.16.2.32/48. Which configuration resolves the issue?

R1(config)#route-map REDIST permit 10

R1(config-route-map) #match Ip address 15

R1 (config-route-map) #exit

R1(config)# access-list 15 permit 172.16.0.0 0.0.255.255

R1(config-router) #router eigrp 100

R1(config-router) #redistrlbute ospf 1 route-map REDIST

R1(oonfig-router) #router ospf 1

R2(config-router) #redistribute eigrp 100 subnets metric 100C.

R1(config-router > #routereigrp 100

R1(config-router > #redistribute ospf 1 metric 1000000 1111

R1(config)#route-map REDIST permit 10

R1(config-roule-map) #match ip address 15

R1 (config-route-map) #exlt

R1(config)# access-list 15 permit 172.16.0.0 0.0.255.255

R1(config-router) #router ospf 1

R1(config-router) #redistrlbute elgrp 100 subnets route-map REDIST

Full Access

Question # 71

What is the function of BFD?

It provides uniform failure detection regardless of media type.

It creates high CPU utilization on hardware deployments.

It negotiates to the highest version if the neighbor version differs.

It provides uniform failure detection on the same media type.

Full Access

Question # 72

R1 and R2 are configured as eBGP neighbor , R1 is in AS100 and R2 is in AS200. R2 is advertising these networks to R1:

The network administrator on R1 must improve convergence by blocking all subnets of 172-16.0.0/16 major network with a mask lower than 23 from coming in, Which set of configurations accomplishes the task on R1?

ip prefix-list PL-1 deny 172.16.0.0/16 le 23ip prefix-list PL-1 permit 0.0.0.0/0 le 32!router bgp 100neighbor 192.168.100.2 remote-as 200neighbor 192.168.100.2 prefix-list PL-1 in

ip prefix-list PL-1 deny 172.16.0.0/16 ge 23ip prefix-list PL-1 permit 0.0.0.0/0 le 32!router bgp 100neighbor 192.168.100.2 remote-as 200neighbor 192.168.100.2 prefix-list PL-1 in

access-list 1 deny 172.16.0.0 0.0.254.255access-list 1 permit any!router bgp 100neighbor 192.168.100.2 remote-as 200neighbor 192.168.100.2 distribute-list 1 in

ip prefix-list PL-1 deny 172.16.0.0/16ip prefix-list PL-1 permit 0.0.0.0/0!router bgp 100neighbor 192.168.100.2 remote-as 200neighbor 192.168.100.2 prefix-list PL-1 in

Full Access