Summer Sale Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: v4s65

300-410 Exam Dumps - Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)

Go to page:
Question # 25

Refer to the exhibit.

Which two actions restrict access to router R1 by SSH? (Choose two.)

A.

Configure transport input ssh on line vty and remove sequence 30 from access list 100.

B.

Configure transport output ssh on line vty and remove sequence 20 from access list 100.

C.

Remove class-map ANY from service-policy CoPP

D.

Configure transport output ssh on line vty and remove sequence 10 from access list 199.

E.

Remove sequence 10 from access list 100 and add sequence 20 deny tcp any any eq telnet to access list 199

Full Access
Question # 26

Refer to the exhibit.

To provide reachability to network 10.1.1.0 /24 from R5, the network administrator redistributes EIGRP into OSPF on R3 but notices that R4 is now taking a ........... path through R5 to reach 10.1.1.0/24 network. Which action fixes the issue while keeping the reachability from R5 to 10.1.1.0/24 network?

A.

Change the administrative distance of the external EIGRP to 90.

B.

Apply the outbound distribution list on R5 toward R4 in OSPF.

C.

Change the administrative distance of OSPF to 200 on R5.

D.

Redistribute OSPF into EIGRP on R4

Full Access
Question # 27

Which configuration feature should be used to block rogue router advertisements instead of using the IPv6 Router Advertisement Guard feature?

A.

VACL blocking broadcast frames from nonauthorized hosts

B.

PVLANs with promiscuous ports associated to route advertisements and isolated ports for nodes

C.

PVLANs with community ports associated to route advertisements and isolated ports for nodes

D.

IPv4 ACL blocking route advertisements from nonauthorized hosts

Full Access
Question # 28

Refer to the exhibit. The administrator configured route advertisement to a remote low resources router to use only the default route to reach any network but failed. Which action resolves this issue?

A.

Change the direction of the distribute-list command from out to in.

B.

Remove the line with the sequence number 5 from the prefix list.

C.

Remove the prefix keyword from the distribute-list command.

D.

Remove the line with the sequence number 10 from the prefix list.

Full Access
Question # 29

Which IGPs are supported by the MPLS LDP autoconfiguration feature?

A.

RIPv2 and OSPF

B.

OSPF and EIGRP

C.

OSPF and ISIS

D.

ISIS and RIPv2

Full Access
Question # 30

Refer to Exhibit.

A network administrator has successfully configured DMVPN topology between a hub and two spoke routers. Which two configuration commands should establish direct communications between spoke 1 and spoke 2 without going through the hub? (Choose two).

A.

At the hub router, configure the ip nhrp shortcut command.

B.

At the spoke routers, configure the ip nhrp spoke-tunnel command.

C.

At the hub router, configure ip nhrp redirect the command

D.

At the spoke routers, configure the ip nhrp shortcut command.

E.

At the hub router, configure tne Ip nhrp spoke-tunnel command

Full Access
Question # 31

Refer to the exhibits.

A user on the 192.168.1.0/24 network can successfully ping 192.168.3.1, but the administrator cannot ping 192.168.3.1 from the LA router. Which set of configurations fixes the issue?

A)

B)

C)

D)

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Full Access
Question # 32

What are two functions of MPLS Layer 3 VPNs? (Choose two.)

A.

LDP and BGP can be used for Pseudowire signaling.

B.

It is used for transparent point-to-multipoint connectivity between Ethernet links/sites.

C.

BGP is used for signaling customer VPNv4 routes between PE nodes.

D.

A packet with node segment ID is forwarded along with shortest path to destination.

E.

Customer traffic is encapsulated in a VPN label when it is forwarded in MPLS network.

Full Access
Go to page: