300-410 Exam Dumps - Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)

Go to page:

<< First
Prev
3
4
5
6
7
8
9
10
11
12
Next
Last >>

Question # 57

Refer to the exhibit. A network administrator configured NetFlow data, but the data is not visible at the NetFlow collector. Which configuration allows the router to send the records?

Configure the management interface in the global routing table to send the records.

Configure a different interface to send the records.

Configure the NetFlow collector to listen at export-protocol netflow-v5.

Rectify NetFlow collector reachability from the management interface.

Full Access

Question # 58

Refer to the exhibit. Users are experiencing slow response times from critical application servers connected to the network. The engineer determined from the console log that there is a DOS attack on the interface GigabitEthernet0/0. Which action must the engineer take to resolve the issue?

Configure an access group on GigabitEthernet0/0 to block traffic from 192.168.1.1.

Configure an access group on GigabitEthernet0/0 to block traffic from 172.17.132.95.

Restrict CoPP traffic on the management interface from 172.17.132.95 and 192.168.1.1.

Configure QoS on FastEthernet0/0 to restrict bandwidth usage for 172.17.132.95 and 192.168.1.1.

Full Access

Question # 59

Refer to the exhibit. After recovering from a power failure. Ethernet0/1 stayed down while Ethernet0/0 returned to the up/up state The default route through ISP1 was not reinstated m the routing table until Ethernet0/1 also came up Which action resolves the issue?

Reference the track object 1 in both static default routes

Remove the references to the interface names from both static default routes

Configure the default route through ISP1 with a higher administrative distance than 2.

Add a static route to the 8 8.8 8/32 destination through the next hop 203.0.113.1

Full Access

Question # 60

Refer to the exhibit R2 has been receiving routes from R4 that originated outside AS300 A network engineer configured an AS-Path ACL to avoid adding these routes to the R2 BGP table but the routes are still present in the R2 routing table Which action resolves the issue?

Replace as-path access-list 1 with the ip as-path access-list 1 permit A300$ command

Replace as-path access-list 1 with the ip as-path access-list 1 permit ..300." command

Replace as-path access-list 1 with the ip as-path access-list 1 permit A300_ command.

Replace as-path access-list 1 with the ip as-path access-list 1 permit A300." command

Full Access

Question # 61

Refer to the exhibit. A network engineer configured routers R1 and R2 with MP-BGP. The engineer noticed that the routers cannot exchange any IPv6 routes, however, the IPv4 neighbor relationship is working fine. Which configuration must the engineer apply to router R2 to exchange IPv6 routes?

Ipv6cef I Interface Loopback100Ipv6 address 2001: DB8:128::2/128 Interface GigabitEthernet1/0Ipv6 address 2001:DB8:1::2/64 I router bgp 65002no bgp default ipv4-unlcastneighbor 2001: DB8:1::1 emote-as 65001Iaddress-family ipv6network 2001:DB8:128::2/128neighbor 2001:DB8:1::1 activate

Ipv6 unicast-routingipv6 cefInterface Loopback100ipv6 address 2001: DB8:12C:2 129Iinterface GigabitEthernet1/0ipv6 address 2001: DB8:1::2 64description AS65001 ID B466:A83D:3D7::1!router bgp 65002no bgp default Ipv4-unicastneighbor 2001: DB8:1::1 remote-as 65001!address-family Ipv4neighbor 2001:DB8:1::1 activate

Ipv6 unicast-routingipvG cefIInterface Loopback100Ipv6 address 2001:DB8:128::2/128 I interface GigabitEthernet1/0ipv6 address 2001:DB8:1::2/64!router bgp 65002 no bgp default ipv4-unicast neighbor 2001: DB8:1::1 remote-as 65001 !address-family ipv6 network 2001:DB8:128::2I128

Ipv6 unicast-routing Ipv6 cef Iinterface Loopback100 ipv6 address 2001: DB8:128::2/128 !interface GigabitEthernet1/0 ipv6 address 2001:DB8:1::2/64 irouter bgp 65002 no bgp default ipv4-unicast neighbor 2001: DB8:1::1 remote-as 65001 !address-family ipv6 network 2001:DB8:128::2/128 neighbor 2001:DB8:1::1 activate

Full Access

Question # 62

Refer to the exhibit While troubleshooting an issue on the network, an engineer notices that a TCP Connect operation failed on port 3000 between R101 and R201. Which command must be configured on R201 to respond to the R101 IP SLA configurations with a control connection on UDP port 1967?

ip sla responder udp-echo ipaddress 1.1.1.1 port 1967

ip sla responder tcp-connect ipaddress 1.1.1.1 port 3000

ip sla responder tcp-connect ipaddress 2.2.2.2 port 3001

ip sla responder

Full Access

Question # 63

Refer to the exhibit.

An engineer configured NetFlow to capture traffic information through the router, but it iOS not working as expected. Which action captures the flow information from this router to the collector?

Change the interface configuration FLOW-MONITOR-1 from input to output.

Configure a flow exporter under flow FLOW-MONITOR-1.

Configure more than one flow exporter destination addresses.

Change the flow exporter transport protocol from UDP to TCP

Full Access

Question # 64

Refer to the exhibit.