New Year Sale Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: scxmas70

  1. Home
  2. Cisco
  3. CCNA
  4. 200-301 - Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1

200-301 Exam Dumps - Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1

Searching for workable clues to ace the Cisco 200-301 Exam? You’re on the right place! ExamCert has realistic, trusted and authentic exam prep tools to help you achieve your desired credential. ExamCert’s 200-301 PDF Study Guide, Testing Engine and Exam Dumps follow a reliable exam preparation strategy, providing you the most relevant and updated study material that is crafted in an easy to learn format of questions and answers. ExamCert’s study tools aim at simplifying all complex and confusing concepts of the exam and introduce you to the real exam scenario and practice it with the help of its testing engine and real exam dumps

Go to page:
Question # 209

Drag and drop the TCP/IP protocols from the left onto the transmission protocols on the right

Full Access
Question # 210

Which goal is achieved by the implementation of private IPv4 addressing on a network?

A.

provides an added level of protection against Internet exposure

B.

provides a reduction in size of the forwarding table on network routers

C.

allows communication across the Internet to other private networks

D.

allows servers and workstations to communicate across public network boundaries

Full Access
Question # 211

Which action prevents debug messages from being sent via syslog while allowing other messages when an abnormally high number of syslog messages are generated by a device with the debug process turned on?

A.

Use an access list to filter out the syslog messages.

B.

Turn off the logging monitor in global configuration mode.

C.

Disable logging to the console.

D.

Set the logging trap severity level to informational.

Full Access
Question # 212

Refer to the exhibit.

An engineer is checking the routing table in the main router to identify the path to a server on the network. Which route does the router use to reach the server at 192.168.2.2?

A.

S 192.168.0.0/20 [1/0] via 10.1.1.1

B.

S 192.168.2.0/29 [1/0] via 10.1.1.1

C.

S 192.168.2.0/28 [1/0] via 10.1.1.1

D.

S 192.168.1.0/30 [1/0] via 10.1.1.1

Full Access
Question # 213

Which IPsec transport mode encrypts the IP header and the payload?

A.

pipe

B.

control

C.

transport

D.

tunnel

Full Access
Question # 214

Refer to the exhibit.

A network engineer must configure router R1 with a host route to the server. Which command must the engineer configure?

A.

R1(conftg)#lp route 10.10.10.0 255.255.255.0 192.168.0.2

B.

R1(Config)#lp route 10.10.10.10 265.255.255.255 192 168.0.2

C.

R1(config)#ip route 192.168.0.2 255.255.255.255 10.10.10.10

D.

R1(config)3|p route 0.0.0.0 0.0 0.0 192 168.0.2

Full Access
Question # 215

What is the difference between SNMP traps and SNMP polling?

A.

SNMP traps are used for proactive monitoring, and SNMP polling is used for reactive monitoring.

B.

SNMP traps send periodic updates via the MIB, and SNMP polling sends data on demand.

C.

SNMP traps are initiated by the network management system, and network devices initiate SNMP polling.

D.

SNMP traps are initiated using a push model at the network device, and SNMP polling is initiated at the server.

Full Access
Question # 216

What determines the sequence in which materials are planned during the material requirements planning (MRP) run?

A.

The control parameters of the MRP run

B.

The creation date of the materials

C.

The low-level code of the materials

D.

The replenishment lead time of the materials

Full Access
Go to page:

Hot Exams

AZ-900 Dumps
200-301 Dumps
350-401 Dumps
350-701 Dumps
AZ-104 Dumps
CS0-003 Dumps
N10-009 Dumps
SY0-701 Dumps
CAS-005 Dumps
PT0-003 Dumps
ZDTA Dumps