Black Friday Countdown: 75% Off Exam Bundles! Use coupon code below before time runs out! - Ends in 0d 00h 00m 00s - Coupon code: 75vsure

HPE7-A08 Exam Dumps - HPE Aruba Networking Certified Professional - Switching

Searching for workable clues to ace the HP HPE7-A08 Exam? You’re on the right place! ExamCert has realistic, trusted and authentic exam prep tools to help you achieve your desired credential. ExamCert’s HPE7-A08 PDF Study Guide, Testing Engine and Exam Dumps follow a reliable exam preparation strategy, providing you the most relevant and updated study material that is crafted in an easy to learn format of questions and answers. ExamCert’s study tools aim at simplifying all complex and confusing concepts of the exam and introduce you to the real exam scenario and practice it with the help of its testing engine and real exam dumps

Go to page:
Question # 41

You are reviewing the configuration of a VSX LAG and have noticed the command LACP fallback. Why might this have been configured?

A.

For operation using a single partner LACP interface.

B.

For backward compatibility with LACP v1.

C.

To support provisioning a gateway without LACP.

D.

To allow operation with active or passive LACP.

Full Access
Question # 42

You are deploying CX 6300 switches and AP-615 access points at a hospital providing connectivity to critical medical devices. Which feature should you enable on the switch to provide the highest uptime for the Wi-Fi network? (Choose two.)

A.

Fast РоЕ

B.

Quick PoE

C.

Uninterruptable PoE

D.

Always-on PoE

Full Access
Question # 43

You have added a switch with existing configuration to an existing group in HPE Aruba Networking Central but the configuration is not synchronizing. What could cause this?

A.

Only switches with factory default config can be added to a group with existing config.

B.

HPE Aruba networking Central has not been enabled on the local switch configuration.

C.

The switch is configured in a VSX pair, which HPE Aruba Networking Central does not support.

D.

The switch is still pending authorization on the organization settings page.

Full Access
Question # 44

Your customer’s CX switches are managed in HPE Aruba Networking Central. They have recently connected some new AP-615 access points and want to be notified if the switches have any capacity issues. Which alerts should you enable? (Choose two.)

A.

Switch Uplink Port Usage

B.

Switch Link Status Change

C.

Switch Port Tx Rate

D.

Switch PoE Utilization

E.

Switch Port Rx Rate

Full Access
Question # 45

Which data format do CX switches support for the REST API?

A.

XML

B.

YAML

C.

JSON

D.

SOAP

Full Access
Question # 46

Refer to the exhibit:

A senior network architect has created the configuration above. You are implementing the setup in building A and D. The actual fiber distance between the building locations is: 90m / 295ft utilizing OM4 cabling.

What needs to be changed on the configuration based on the actual environmental conditions or is valid about the configuration?

A.

system interface-group 1 speed 1 /10g for ports 1-4 is the default for CX 8325

B.

system interface-group 1 speed 25g for ports 1-4 is the default for CX 8325

C.

system interface-group 1 speed 1/10g for ports 1-12 is the default for CX 8325

D.

system interface-group 1 speed 25g for ports 1-12 is the default for CX 8325

Full Access
Question # 47

Refer to the exhibit from an HPE Aruba Networking CX6000:

Two CX 6000 switches are configured with the same configuration for LAG 1. What needs to be done to remove the LACP block state?

A.

On one of the switches, change the LACP mode to passive

B.

Change the LACP mode from passive to active on one of the switches

C.

Change the LACP mode from passive to static on one of the switches

D.

On both of the switches, change the LACP timeout to short

Full Access
Question # 48

Match the terminology related to 802.1x authentication.

Full Access
Go to page: