Black Friday Countdown: 75% Off Exam Bundles! Use coupon code below before time runs out! - Ends in 0d 00h 00m 00s - Coupon code: 75vsure

HPE7-A08 Exam Dumps - HPE Aruba Networking Certified Professional - Switching

Searching for workable clues to ace the HP HPE7-A08 Exam? You’re on the right place! ExamCert has realistic, trusted and authentic exam prep tools to help you achieve your desired credential. ExamCert’s HPE7-A08 PDF Study Guide, Testing Engine and Exam Dumps follow a reliable exam preparation strategy, providing you the most relevant and updated study material that is crafted in an easy to learn format of questions and answers. ExamCert’s study tools aim at simplifying all complex and confusing concepts of the exam and introduce you to the real exam scenario and practice it with the help of its testing engine and real exam dumps

Go to page:
Question # 25

For the aggregation layer, you must configure two new HPE Aruba Networking CX 6200M (VSF) switches. LACP link aggregations to downstream access switches using redundant ports from both switches are required.

Which configuration example would create the required lag setup on both switches utilizing HPE Aruba Networking clustering and stacking technologies?

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Full Access
Question # 26

Given the QoS queueing configuration below for a 1000Mbps interface, how much bandwidth will be available to Local Priority 4 traffic if no other traffic type is to be sent?

A.

1000Mbps

B.

500Mbps

C.

200Mbps

D.

100Mbps

Full Access
Question # 27

In an attempt to clear the switch configuration, you’ve issued the command erase all zeroize. What is the result of this task?

A.

The switch clears all user credentials and retains the running configuration.

B.

The switch restores the factory-installed AOS-CX image to the switch.

C.

The switch runs a secure erase task, deleting the startup-config, and retains admin credential password.

D.

The switch runs a secure erase task, deleting all customer data, and may run up to an hour.

Full Access
Question # 28

With the given output from an HPE Aruba Networking CX 6300:

Which statement about the output above is true?

A.

The accepted AS paths are defined in the aspath-list.

B.

The defined route-map is used in BGP with neighbor remote-as export.

C.

The advertised AS paths are configured in an IP prefix-list.

D.

The route-map with aspath-list intended for iBGP peers.

Full Access
Question # 29

Refer to the exhibit:

According to the HPE Aruba Networking VSX best practices, what would need to be changed on the configuration?

A.

Replace the CX 8325 1/1/47 and 1/1/48 ports with SFP28 connectivity.

B.

Replace the CX 8325 1/1/47 and 1/1/48 ports with SFP56 connectivity.

C.

Replace the CX 6300 [1-2]/1/49 and [1-2] /1/50 ports with QSFP28 connectivity.

D.

Replace the CX 6300 [1-2]/1/49 and [1-2] /1/50 ports with SFP56 connectivity.

Full Access
Question # 30

While troubleshooting a scenario in which the customer has added two new line cards on an HPE Aruba Networking CX 6400 switch, the LEDs on the line card do not show light on the first card.

Which troubleshooting methodology should you use to isolate the problem?

A.

Spot the difference by comparing the switch configurations.

B.

Divide and conquer by swapping the line cards in their slot.

C.

Follow the path and check the connectivity from the access switch to the CX 6400.

D.

Replace the configuration using the previous checkpoint on the switch.

Full Access
Question # 31

You are implementing a directly connected routing plan using OSPF on an HPE Aruba Networking CX 6200 and ISP router. What would be the impact of changing the network type to point-to-point?

A.

It will reduce the number of LSA type-2 advertisements

B.

A larger number of OSPF routes would be supported

C.

It will increase the number of LSA type-3 advertisements

D.

The configuration would remain as the default

Full Access
Question # 32

Refer to the partial exhibit from an HPE Aruba Networking CX 8325:

A new port 1/1/44 needs to be configured to connect to a 29301, which has the following configuration:

Which configuration would be used?

A.

B.

C.

D.

Full Access
Go to page: