Weekend Sale Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: scxmas70

  1. Home
  2. Cisco
  3. CCNP Collaboration
  4. 300-815 - Implementing Cisco Advanced Call Control and Mobility Services (CLACCM)

300-815 Exam Dumps - Implementing Cisco Advanced Call Control and Mobility Services (CLACCM)

Go to page:
Question # 4

Refer to the exhibit. An administrator configured a new SIP trunk between Cisco UCM and Cisco Unified Border Element. Calls that use this new trunk are failing, and debugs from the Cisco Unified Border Element do not show any signaling received from Cisco UCM. The administrator verified that OPTIONS is enabled on the SIP profile configured on the trunk on Cisco UCM. The route pattern matched for this call is correctly configured to send calls to the Cisco Unified Border Element using this new trunk. What is the cause of this failure?

A.

The calling search space on the calling line/device does not contain the partition of the route pattern

B.

The called party number is not complete because it contains only 7 digits

C.

A connectivity issue between Cisco UCM and Cisco Unified Border Element prevents Cisco UCM from receiving a response to the OPTIONS it is sending to Cisco Unified Border Element

D.

There are multiple matches for the dialed number, and Cisco UCM is trying to send the call to SEP2834A2824611 rather than Cisco Unified Border Element

Full Access
Question # 5

Signal number reach call phone that not answered are leaving voicemails on the cell phone rather the corporate mailbox. Which two options will resolve this issue? (Choose two.)

A.

Check the Enable Extend and Connect checkbox

B.

Check the Enable Unified Mobility features checkbox

C.

Decrease the T302 timer

D.

Decrease the T301 timer Decrease the Answer Too Late timer

Full Access
Question # 6

Refer to the exhibit.

An engineer configures Cisco Unified Border Element to connect the enterprise VoIP network with a SIP telephony provider. Calls are not working in either direction. What must be configured in the dial peer 1 to fix the issue?

A.

answer-address 555 ……..

B.

codec g729

C.

session-protocol sipv2

D.

incoming called number 555…….

Full Access
Question # 7

Refer to the exhibit.

Calls incoming from the provider are not working through newly set up Cisco Unified Border Element. Provider engineers get the 404 Not Found SIP message. Incoming calls are coming from the provider with called number “222333444” and Cisco Unified Communications Manager is expecting the called number to be delivered as “444333222”. The administrator already verified that the IP address of the Cisco Unified CM is set up correctly and there are no dial peers configured other than those shown in the exhibit. Which action must the administrator take to fix the issue?

A.

Change the destination-pattern on the outgoing dial peer to match “444333222”.

B.

Set up translation-profile on the incoming dial peer to match incoming traffic.

C.

Create specific matching for “222333444” on the incoming dial peer.

D.

Fix the voice translation-rule to match specifically number “222333444” and change it to “444333222”.

Full Access
Question # 8

When the services key is pressed Cisco Extension Mobility does not show up. What is the cause of the issue?

A.

The URL configured for Cisco Extension Mobility is not correct.

B.

Cisco Extension Mobility Service is not running.

C.

The phone is not subscribed to Cisco Extension Mobility Service.

D.

Cisco Extension Mobility is not enabled in the Phone Configuration Window (Device > Phone)

Full Access
Go to page:

Hot Exams

ADM-201 Dumps
Platform-App-Builder Dumps
AZ-500 Dumps
350-701 Dumps
SY0-601 Dumps
NCSE-Core Dumps
PDP9 Dumps
DP-203 Dumps
AZ-700 Dumps
NSE7_EFW-7.0 Dumps
Integration-Architect Dumps
CS0-003 Dumps