Summer Sale Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: v4s65

300-815 Exam Dumps - Implementing Cisco Advanced Call Control and Mobility Services (CLACCM)

Go to page:
Question # 25

Refer to the exhibit.

Users report that when they dial the emergency number 9911 from any internal phone, it takes a long time to connect with the emergency operator. Which action resolves this issue?

A.

Adjust the service parameter T302 timet to the desired value.

B.

Adjust the service parameter T204 timer to the desired value.

C.

Check the Urgent Priority check box under 9.911 pattern.

D.

Point the emergency pattern directly to the PSTN gateway.

Full Access
Question # 26

What is a function of the metadata carried in SIP sessions between the recording client and the recording server?

A.

It forks RTP media to the recorder.

B.

It provides advanced capabilities, such as speech analytics.

C.

It sets up a new SIP session

D.

It identifies the participant change due to transfers during the call.

Full Access
Question # 27

Some Cisco mobility users cannot resume calls on the desk phone after they hang up on a mobile phone. The users have Cisco IP phones registered to the Cisco UCM. Which set of configuration steps resolve the issue?

A.

Add voice call disc-pi-off on the voice gateway. On Call Manager, set the Retain Media on Disconnect with PI for Active Call service parameter to True.

B.

Add voice call disc-pi-on on the voice gateway. On Call Manager, set the Retain Media on Disconnect with PI for Active Call service parameter to False.

C.

Add voice call disc-pi-off on the voice gateway. On Call Manager, set the Retain Media on Disconnect with PI for Active Call service parameter to False.

D.

Add voice call disc-pi-on on the voice gateway. On Call Manager, set the Retain Media on Disconnect with PI for Active Call service parameter to True.

Full Access
Question # 28

An engineer is configuring Cisco UCME to support SIP endpoints. The engineer wants to limit the system to 20 SIP phones and 50 directory numbers. Which code completes this configuration?

A.

telephony-service

mode cme

max-ephone 20

max-dn 50

B.

voice register global

mode cme

max-ephone 20

max-dn 50

C.

telephony-service

mode cme

max-pool 20

max-dn 50

D.

voice register global

mode cme

max-pool 20

max-dn 50

Full Access
Question # 29

An engineer needs to configure a translation pattern in Cisco UCM to match dialed numbers that start with 9011 so that the calls can be routed with a single route pattern of VH If the engineer uses translation pattern 9011.! which two called party transformation settings must be configured in Cisco UCM? (Choose two.)

A.

set Prefix Digits (Outgoing Calls) to +

B.

set Called Party Transform Mask to +!

C.

set Discard Digits to Predot

D.

set Called Party Numbering Plan to International

E.

set Called Party Number Type to International

Full Access
Question # 30

A newly deployed site in Pennsylvania uses SIP-to-SIP legs on a Cisco Unified Border Element. The administrator wants to match the incoming dial peer based on the calling number. Which configuration is needed in the dial-peer?

A.

answer-address

B.

incoming called-number

C.

destination calling

D.

destination-pattern

Full Access
Question # 31

An engineer has temporarily disabled toll fraud prevention for SIP line calls on a Cisco CME12.6x and must enforce security and toll fraud prevention for the SIP line side on Cisco Unified CME. Which configuration must be used to start this process?

A.

voice service volp

Ip address trusted list

B.

voice service volp

enablo ip address trust authentication

C.

voice service volp

enable Ip address trust list

D.

voice service volp

ip address trusted authenticate

Full Access
Question # 32

A company is using a H.323 gateway for PSTN calls from Cisco phones connected to a Cisco UCM cluster. There are reports of problems getting audio on these incoming calls from the PSTN. The phone rings, but nothing is heard and the call disconnects.

Which command troubleshoots this issue?

A.

debug voice h323 inout

B.

debug h245 pstn

C.

debug h245 asn1

D.

debug voice sip inout

Full Access
Go to page: