200-301 Exam Dumps - Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1

Searching for workable clues to ace the Cisco 200-301 Exam? You’re on the right place! ExamCert has realistic, trusted and authentic exam prep tools to help you achieve your desired credential. ExamCert’s 200-301 PDF Study Guide, Testing Engine and Exam Dumps follow a reliable exam preparation strategy, providing you the most relevant and updated study material that is crafted in an easy to learn format of questions and answers. ExamCert’s study tools aim at simplifying all complex and confusing concepts of the exam and introduce you to the real exam scenario and practice it with the help of its testing engine and real exam dumps

Go to page:

<< First
Prev
2
3
4
5
6
7
8
9
10
11
Next
Last >>

Question # 49

Which two actions influence the EIGRP route selection process? (Choose two)

The router calculates the reported distance by multiplying the delay on the exiting Interface by 256.

The router calculates the best backup path to the destination route and assigns it as the feasible successor.

The router calculates the feasible distance of all paths to the destination route

The advertised distance is calculated by a downstream neighbor to inform the local router of the bandwidth on the link

The router must use the advertised distance as the metric for any given route

Full Access

Question # 50

Which protocol does an access point use to draw power from a connected switch?

Internet Group Management Protocol

Adaptive Wireless Path Protocol

Cisco Discovery Protocol

Neighbor Discovery Protocol

Full Access

Question # 51

Which command must be entered when a device is configured as an NTP server?

ntp authenticate

ntp server

ntp peer

ntp master

Full Access

Question # 52

Refer to me exhibit.

Which action is taken by the router when a packet is sourced from 10.10.10.2 and destined for 10.10.10.16?

It uses a route that is similar to the destination address

It discards the packets.

It floods packets to all learned next hops.

It Queues the packets waiting for the route to be learned.

Full Access

Question # 53

Which function does an SNMP agent perform?

it sends information about MIB variables in response to requests from the NMS

it requests information from remote network nodes about catastrophic system events.

it manages routing between Layer 3 devices in a network

it coordinates user authentication between a network device and a TACACS+ or RADIUS server

Full Access

Question # 54

Which two must be met before SSH can operate normally on a Cisco IOS switch? (Choose two)

The switch must be running a k9 (crypto) IOS image

The Ip domain-name command must be configured on the switch

IP routing must be enabled on the switch

A console password must be configured on the switch

Telnet must be disabled on the switch

Full Access

Question # 55

Refer to the exhibit.

The image server and client A are running an application that transfers an extremely high volume of data between the two. An engineer is configuring a dedicated circuit between R1 and R2. Which set of commands must the engineer apply to the routers so that only traffic between the image server and client A is forces to use the new circuit?

R1(config)#ip route 10.10.13.10 255.255.255.255 10.10.10.6R2(config)#ip route 192.168.0.100 255.255.255.255 10.10.10.5

R1(config)#ip route 10.10.13.10 255.255.255.128 10.10.10.6R2(config)#lp route 192.168.0.100 255.255.255.0 10.10.10.5

R1(config)#ip route 10.10.13.10 255.255.255.252 10.10.10.6R2(config)#tp route 192.168.0.100 255.255.255.252 10.10.10.5

R1(config)#ip route 10.10.13.10 255.255.255.255 10.10.10.2R2(config)#ip route 192.168.0.100 255.255.255.255 10.10.10.1

Full Access

Question # 56

Exhibit.

The switches are connected via a Cat5 Ethernet cable that was successfully tested. The Interfaces are configured as access ports and are both in a 'down" status. What is the cause of this issue?

The switches are configured with incompatible duplex settings.

The distance between the two switches is not supported by Cut5.

The speed settings on the switches are mismatched.

The portfast command is missing from the configuration.

Full Access

Go to page: