200-301 Exam Dumps - Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1

It detects the device is a powered device. In PoE auto mode, the switch detects that the connected endpoint is a powered device and allocates power based on negotiation and device requirements. Static mode reserves power whether the device actually needs that amount or not, which can waste available PoE budget on a switch. Power policing is a related feature but it is not the basic advantage of auto mode over static mode. Cisco CCNA 200-301 v1.1 Network Access includes PoE behavior because access points, IP phones, and cameras depend on switch-provided power. The corrected answer is that auto mode detects the powered device. That is the operational reason auto allocation is generally preferred for access points and other PoE endpoints when the switch can negotiate and manage power dynamically.

array. Automation questions require recognizing data structures, HTTP methods, APIs, controllers, and the separation of northbound and southbound communication. Cisco CCNA 200-301 v1.1 includes this under Automation and Programmability, where the expected skill is to identify the feature that actually creates the observed behavior or meets the configuration goal. The wording usually contains the decisive clue: a prefix length, a VLAN role, a protocol version, a wireless security standard, or a management-plane function. Distractors mix application-facing and device-facing roles or confuse values, keys, arrays, and objects. In an operational network, choosing the wrong option would typically cause failed connectivity, insecure management, poor wireless behavior, or incorrect forwarding. The selected answer matches the Cisco configuration model and is retained as the verified answer.

Discovery request. Wireless questions depend on AP mode, WLAN security, RF band selection, controller interfaces, and client roaming or authentication behavior. Cisco CCNA 200-301 v1.1 includes this under Network Access, where the expected skill is selecting the feature that actually produces the requested network behavior. The wording normally gives the clue: protocol family, address scope, trunk state, route preference, security mode, API method, or controller role. Wrong options confuse encryption with authentication, local switching with tunneling, or controller management with client data handling. In production, choosing the wrong option would typically cause failed client access, a broken route, insecure management, or an automation workflow that targets the wrong interface. The selected answer is the Cisco-consistent behavior for this item.

link aggregation. Wireless questions depend on AP mode, WLAN security, RF band selection, controller interfaces, and client roaming or authentication behavior. Cisco CCNA 200-301 v1.1 includes this under Network Access, where the expected skill is selecting the feature that actually produces the requested network behavior. The wording normally gives the clue: protocol family, address scope, trunk state, route preference, security mode, API method, or controller role. Wrong options confuse encryption with authentication, local switching with tunneling, or controller management with client data handling. In production, choosing the wrong option would typically cause failed client access, a broken route, insecure management, or an automation workflow that targets the wrong interface. The selected answer is the Cisco-consistent behavior for this item.

It floods the frame out of every port except the source port.. If the destination MAC address is missing from the switch MAC address table, the switch treats the frame as an unknown unicast. It floods the frame out ports in the same VLAN except the port on which it arrived. It does not err-disable the port, drop the frame from the table, or create a broadcast storm as the default behavior. Cisco CCNA 200-301 v1.1 Network Access expects candidates to know that VLAN boundaries still apply during flooding. Because host A is in VLAN 2, the switch floods only within VLAN 2, not through unrelated VLANs. The corrected answer is that the switch floods the frame out every eligible port except the source port.

Answer C,D is correct: C. SW1(config)#line vty 0 15 SW1(config-line)#transport input ssh; D. SW1(config)# crypto key generate rsa. Secure encrypted remote management requires the VTY lines to accept SSH and the switch to have RSA keys available for SSH operation. The enable secret protects privileged EXEC mode, but it does not by itself enable encrypted remote access. A trunk command is unrelated to management-plane security. A local username may also be required depending on the existing configuration, but the two choices that directly enable encrypted remote management from the listed commands are transport input ssh and crypto key generate rsa. Cisco CCNA 200-301 v1.1 Security Fundamentals expects engineers to know the SSH prerequisites: hostname/domain context, RSA keys, appropriate line transport, and authentication. The corrected answer pair is the VTY SSH transport command and RSA key generation.

ip ospf network point-to-point. Routing and redundancy questions are solved by applying longest-prefix match, administrative distance, metrics, and gateway-redundancy behavior in the correct order. Cisco CCNA 200-301 v1.1 includes this under IP Connectivity, where the expected skill is selecting the feature that actually produces the requested network behavior. The wording normally gives the clue: protocol family, address scope, trunk state, route preference, security mode, API method, or controller role. Incorrect choices point to the wrong next hop, choose the wrong route source, or confuse routing with Layer 2 behavior. In production, choosing the wrong option would typically cause failed client access, a broken route, insecure management, or an automation workflow that targets the wrong interface. The selected answer is the Cisco-consistent behavior for this item.

Reboot the WLC. Cisco WLC Link Aggregation is not a change that fully takes effect merely by re-enabling interfaces or clearing MAC tables. After LAG is enabled, disabled, or reconfigured, the controller must be rebooted for the new aggregation behavior to become active. Reassociating access points is not the required task; the controller platform itself needs the restart. Cisco CCNA 200-301 v1.1 Network Access expects candidates to recognize WLC operational requirements because controller changes can affect all AP and client traffic. The corrected answer is reboot the WLC. This is why LAG changes on a production controller should be planned as a maintenance-window activity rather than treated as a nondisruptive switchport-only change.