200-301 Exam Dumps - Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1

R2# configure terminal

R2(config)# interface Ethernet0/0

R2(config-if)# ip ospf priority 255

R2(config-if)# exit

R2(config)# interface Ethernet0/1

R2(config-if)# ip ospf priority 255

R2(config-if)# exit

R2(config)# router ospf 30

R2(config-router)# router-id 10.22.22.22

R2(config-router)# network 10.0.12.0 0.0.0.3 area 0

R2(config-router)# network 10.0.23.0 0.0.0.15 area 0

R2(config-router)# end

R2# copy running-config startup-config

Verification commands:

R2# show ip ospf neighbor

R2# show ip ospf interface Ethernet0/0

R2# show ip ospf interface Ethernet0/1

R2# show ip protocols

The router ospf 30 command creates the locally significant OSPF process requested by the task. The explicit router-id 10.22.22.22 command prevents R2 from dynamically selecting another active interface address as its router ID. The /30 network requires wildcard mask 0.0.0.3, while the /28 network requires 0.0.0.15; placing both prefixes in area 0 enables OSPF on R2’s links toward R1 and R3 and permits neighbor formation when the remaining OSPF parameters match.

The interface command ip ospf priority 255 gives R2 the maximum OSPF interface priority on both broadcast segments. This makes R2 the strongest DR candidate. OSPF DR elections are non-preemptive, so if a DR election has already completed, the election must be restarted by clearing the relevant OSPF processes or resetting the affected interfaces. Cisco documents that OSPF router IDs identify OSPF instances, while the DR and BDR reduce flooding on broadcast networks; OSPF process numbers do not have to match between neighboring routers.

anycast address. IPv6 questions depend on address scope, prefix representation, and whether the address is unicast, multicast, anycast, link-local, or global. Cisco CCNA 200-301 v1.1 includes this under Network Fundamentals, where the exam expects engineers to recognize the device behavior that actually produces the required outcome. The question is best solved by reading the operational clue rather than choosing a familiar acronym. The wrong choices represent a different IPv6 address behavior or an invalid compressed form. In a production network, the wrong choice would normally create an outage, leave a management or security gap, or send troubleshooting toward the wrong subsystem. The selected answer is the one that matches the control-plane, data-plane, wireless, security, services, or automation mechanism described in the question. That is why it remains the verified answer for this item.

GigabltEthornet0/1. OSPF operation depends on area membership, network type, timers, router ID, priority, and whether a DR/BDR election occurs. Cisco CCNA 200-301 v1.1 includes this under IP Connectivity, where the expected skill is identifying the mechanism that actually satisfies the scenario. The wording usually gives the decisive clue: a protocol number, a route prefix, a control-plane role, a wireless security method, or a management command. Incorrect choices either use the wrong OSPF role, omit a required adjacency condition, or apply a setting that does not affect the stated behavior. In a real network, selecting the wrong option would usually produce a failed adjacency, broken client connectivity, insecure management access, or an incorrect forwarding path. The selected answer matches the Cisco behavior and configuration model required by the question, so it is retained as the verified answer for this item.

Telnet. Wireless operation depends on WLAN identity, AP mode, RF management, client authentication, and controller-based policy enforcement. Cisco CCNA 200-301 v1.1 includes this under Network Access, where the exam expects engineers to recognize the device behavior that actually produces the required outcome. The question is best solved by reading the operational clue rather than choosing a familiar acronym. The distractors confuse WLAN names, authentication, encryption, RF optimization, and controller management functions. In a production network, the wrong choice would normally create an outage, leave a management or security gap, or send troubleshooting toward the wrong subsystem. The selected answer is the one that matches the control-plane, data-plane, wireless, security, services, or automation mechanism described in the question. That is why it remains the verified answer for this item.

switchport trunk allowed vlan add 23. Cisco wireless design separates RF behavior, client authentication, encryption, AP operating mode, and controller management. A WLC centralizes WLAN configuration and AP control, while lightweight APs use CAPWAP to register and exchange control/data information with the controller. Security choices such as WPA2/AES and WPA3/SAE are not interchangeable with older mechanisms such as WEP, TKIP, or RC4. RF questions also depend on channel planning: adjacent cells should avoid overlapping channels, and 5-GHz preference features reduce congestion in the 2.4-GHz band. The incorrect options generally confuse AP mode, authentication, encryption, or controller responsibilities. Cisco CCNA 200-301 v1.1 includes these items because wireless failures often come from using the right-looking feature in the wrong part of the WLAN design. The selected answer is the Cisco-consistent configuration or behavior for this wireless scenario.

Set the Layer 2 Security to None.. Cisco wireless design separates RF behavior, client authentication, encryption, AP operating mode, and controller management. A WLC centralizes WLAN configuration and AP control, while lightweight APs use CAPWAP to register and exchange control/data information with the controller. Security choices such as WPA2/AES and WPA3/SAE are not interchangeable with older mechanisms such as WEP, TKIP, or RC4. RF questions also depend on channel planning: adjacent cells should avoid overlapping channels, and 5-GHz preference features reduce congestion in the 2.4-GHz band. The incorrect options generally confuse AP mode, authentication, encryption, or controller responsibilities. Cisco CCNA 200-301 v1.1 includes these items because wireless failures often come from using the right-looking feature in the wrong part of the WLAN design. The selected answer is the Cisco-consistent configuration or behavior for this wireless scenario.

Client Band Select. Cisco wireless design separates RF behavior, client authentication, encryption, AP operating mode, and controller management. A WLC centralizes WLAN configuration and AP control, while lightweight APs use CAPWAP to register and exchange control/data information with the controller. Security choices such as WPA2/AES and WPA3/SAE are not interchangeable with older mechanisms such as WEP, TKIP, or RC4. RF questions also depend on channel planning: adjacent cells should avoid overlapping channels, and 5-GHz preference features reduce congestion in the 2.4-GHz band. The incorrect options generally confuse AP mode, authentication, encryption, or controller responsibilities. Cisco CCNA 200-301 v1.1 includes these items because wireless failures often come from using the right-looking feature in the wrong part of the WLAN design. The selected answer is the Cisco-consistent configuration or behavior for this wireless scenario.

Answer A,E is correct: A. They alleviate the shortage of public IPv4 addressses.; E. They provide a layer of security from Internet threats.. Security questions in CCNA 200-301 v1.1 require matching the control to the threat or access requirement. Authentication proves identity, authorization controls what the user can do, and accounting records activity. Firewalls inspect and permit or deny traffic based on policy, while ACLs match packet fields in a defined order. VPN and IPsec questions require knowing whether the design protects unicast traffic, supports tunneling, or encrypts the original packet. Password and SSH questions depend on IOS behavior, including encrypted secrets, local users, domain names, and cryptographic images. The incorrect choices often use a valid technology in the wrong role or provide weaker protection. The selected answer is the Cisco-consistent control because it directly satisfies the access, confidentiality, or threat-mitigation requirement stated in the question.