XK0-005 Exam Dumps - CompTIA Linux+ Exam

The issue is caused by the server 192.168.168.53 being unreachable. This server is the DNS server configured in the /etc/resolv.conf file, which is used to resolve domain names to IP addresses. The ping command shows that the server cannot be reached, and the nslookup command shows that the name www.comptia.org cannot be resolved using this server. The other options are incorrect because:

The name www.comptia.org does point to a valid IP address, as shown by the nslookup command using another DNS server (8.8.8.8).

The default route is set on the server, as shown by the ip route command, which shows a default gateway of 192.168.168.1.

The network interface eth0 is connected, as shown by the ip link command, which shows a state of UP for eth0. References: CompTIA Linux+ Study Guide, Fourth Edition, page 457-458, 461-462.

"modify the /etc/fstab text file to automatically mount the new partition by opening it in an editor and adding the following line:

/dev/ xxx 1 /data ext4 defaults 1 2

where xxx is the device name of the storage device"

https://learning.oreilly.com/library/view/mastering-linux-system/9781119794455/b01.xhtml

To configure a new filesystem that needs the capability to be mounted persistently across reboots, two commands are needed: mkfs.ext4 /dev/sdc1 and echo “/dev/sdc1 /data ext4 defaults 0 0” >> /etc/fstab. The first command creates an ext4 filesystem on the device /dev/sdc1, which is the partition that will be used for the new filesystem. The second command appends a line to the /etc/fstab file, which is the configuration file that controls persistent mount points of filesystems. The line specifies the device name, the mount point (/data), the filesystem type (ext4), the mount options (defaults), and the dump and pass values (0 0). The other commands are incorrect because they either do not create or configure a filesystem, or they have wrong syntax or arguments. References: CompTIA Linux+ Study Guide, Fourth Edition, page 409-410, 414-415.

To prevent certain files from being tracked by Git, the administrator can use a .gitignore file (B) in the repository. The .gitignore file can specify patterns of files or directories that Git should ignore. This way, the Terraform state files will not appear in the main branch or any other branch. The other commands are not related to this requirement. References:

[CompTIA Linux+ Study Guide], Chapter 10: Working with Git, Section: Ignoring Files with .gitignore

[How to Use .gitignore File]

The dnf update command will accomplish the task of installing the most recent versions of packages on a RPM-based OS. This command will check for available updates from the enabled repositories and apply them to the system. The apt-get upgrade command is used to install updates on a Debian-based OS, not a RPM-based OS. The rpm -a command is invalid, as -a is not a valid option for rpm. The yum updateinfo command will display information about available updates, but it will not install them. The yum check-update command will check for available updates, but it will not install them. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 19: Managing Packages and Software, page 559.

The command ss -pint will allow the administrator to obtain the needed information about processes that are listening on the network ports of a Linux server. The ss command is a tool for displaying socket statistics on Linux systems. Sockets are endpoints of network communication that allow processes to exchange data over the network. The ss command can show various information about the sockets, such as the state, address, port, protocol, and process. The -pint option specifies the filters and flags that the ss command should apply. The -p option shows the process name and ID that owns the socket. The -i option shows the internal information about the socket, such as the send and receive queue, the congestion window, and the retransmission timeout. The -n option shows the numerical address and port, instead of resolving the hostnames and service names. The -t option shows only the TCP sockets, which are the most common type of sockets used for network communication. The command ss -pint will display the socket statistics for the TCP sockets, along with the process name and ID, the numerical address and port, and the internal information. This will allow the administrator to obtain the needed information about processes that are listening on the network ports of a Linux server. This is the correct command to use to obtain the needed information. The other options are incorrect because they either do not show the socket statistics (tcpdump -nL or lsof -It) or do not show the process name and ID (netstat -pn). References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 12: Managing Network Connections, page 389.

The ip link show eth1 command can be used to check the link status of a network interface named eth1 in a Linux server. It will display information such as the MAC address, MTU, state, and flags of the interface. The ifconfig hw eth1 command is invalid, as hw is not a valid option for ifconfig. The netstat -r eth1 command would display the routing table for eth1, not the link status. The ss -ti eth1 command would display TCP information for sockets associated with eth1, not the link status. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 13: Networking Fundamentals, page 436.

Option C is the only data structure that is written in JSON format. JSON stands for JavaScript Object Notation, and it is a lightweight and human-readable data interchange format. JSON uses curly braces to enclose objects, which consist of key-value pairs separated by commas. JSON uses square brackets to enclose arrays, which consist of values separated by commas. JSON supports six data types: strings, numbers, booleans, null, objects, and arrays. Option C follows these rules and syntax of JSON, while the other options do not. Option A is written in XML format, which uses tags to enclose elements and attributes. Option B is written in YAML format, which uses indentation and colons to define key-value pairs. Option D is written in INI format, which uses sections and equal signs to define key-value pairs. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 21: Automating Tasks with Ansible, page 591.

After installing a new version of a package that includes a configuration file that already exists on the system, such as /etc/httpd/conf/httpd.conf, RPM will create a new file with the .rpmnew extension instead of overwriting the existing file. This allows the administrator to review the default configuration that shipped with this version and compare it with the current configuration before deciding whether to merge or replace the files. The /etc/named.conf.rpmsave file is created by RPM when a package is uninstalled and it contains a configuration file that was modified by the administrator. This allows the administrator to restore the configuration file if needed. The /etc/named.conf file is the main configuration file for the BIND name server, not the httpd web server. The /etc/bind/bind.conf file does not exist by default in Linux systems. References: CompTIA Linux+ (XK0-005) Certification Study Guide, Chapter 19: Managing Packages and Software, page 561.