CWDP-305 Exam Dumps - Certified Wireless Design Professional

Channels 116-124 in the 5 GHz band fall under the Dynamic Frequency Selection (DFS) range. These channels are shared with radar systems, such as those used by airports. When radar activity is detected, Access Points (APs) operating on DFS channels must vacate the channel, leading to potential disruptions in service. In environments near airports, it's advisable to avoid using DFS channels to prevent such interruptions, ensuring a stable and reliable wireless experience for voice devices.

In public WLAN environments, security and privacy are paramount. To prevent clients from communicating directly with each other, many WLANs implement peer-to-peer blocking (also known as client isolation). This feature ensures that each client can communicate with the internet but not with other clients on the same network, thereby enhancing security.

The CWDP-305 Official Study and Reference Guide discusses this feature:

"Client isolation prevents wireless clients from communicating directly with each other, which is especially important in public or guest networks to protect user privacy and security."

Therefore, the inability to detect other devices on the subnet is likely due to peer-to-peer blocking being enabled on the WLAN infrastructure.

In the 5 GHz band, certain channels like 144 are not universally supported across all devices, especially older 802.11n clients. If the AP is operating on channel 144, and the client's regulatory domain or hardware does not support this channel, the SSID will not be visible to the client.

The CWDP-305 Official Study and Reference Guide notes:

"Client devices may not support all channels in the 5 GHz band, depending on their regulatory domain and hardware capabilities. Channel 144, for example, is not supported by all 802.11n clients."

Comprehensive and Detailed Explanation:

In warehouse environments, physical changes can significantly impact WLAN performance. Over time, the addition or rearrangement of inventory (e.g., pallets, shelving) can alter RF propagation, leading to coverage gaps or interference. Therefore, it's essential to inquire about any inventory changes that may have occurred since the initial installation.

Other Options:

A.DHCP lease exhaustion typically affects IP address assignment but is less likely to cause location-specific WLAN issues.

B.Changes in receive gain are hardware-related and less common unless equipment has been replaced or reconfigured.

D.While rogue APs can cause interference, they usually affect broader areas and are less likely to cause isolated issues unless specifically deployed nearby.

Elevator shafts and similar structures can create RF “dead zones” due to their highly attenuating materials like metal. In such cases, simply increasing power or gain typically does not solve the issue due to shadowing. The recommended approach is to move APs or install additional APs on the obstructed side.

From CWDP-305:

“Obstructions such as elevator shafts may require re-positioning or the addition of APs to ensure proper coverage. These obstructions can block RF propagation regardless of transmit power or antenna gain.”

— Reference: CWDP-305 Official Study Guide, Post-Design ValidationandTroubleshooting Chapter

When conducting a site survey, accurately determining ceiling heights is crucial for proper AP placement and coverage prediction.If ladder use is restricted, utilizing a laser distance meter provides a precise and cost-effective solution.Laser measures can quickly and safely determine vertical distances without the need for physical elevation.گروه آموزشی و پژوهشی سیب

The CWDP-305 Official Study and Reference Guide emphasizes:

"Laser distance meters are valuable tools during site surveys, allowing for accurate measurements of ceiling heights and other distances without the need for ladders or lifts."

To measure performance metrics such as throughput and latency, you must associate with the AP and generate/receive real traffic. This type of survey is called an active survey.

From CWDP-305:

“Active surveys assess the end-user experience by collecting real-time data, such as throughput, latency, and packet loss, which cannot be captured by passive surveys.”

Passive surveys only collect information from beacons and probe responses without associating with the AP.

— Reference: CWDP-305 Official Study and Reference Guide, Chapter on Post-Design ValidationandTroubleshooting

Comprehensive and Detailed Explanation:

In the "local MAC" variation of the centralized WLAN architecture, all MAC (Media Access Control) functions are performed by the Access Point (AP). A minimal subset of network control is offloaded to the WLAN controller, which also handles management and monitoring functions. This approach allows for more efficient processing at the edge of the network, reducing latency and improving performance.