300-615 Exam Dumps - Troubleshooting Cisco Data Center Infrastructure (300-615 DCIT) v1.1

The selected resolution is • Set ESX01_B zone to VSAN 20. • Change vHBA1 to VSAN 20 in Service Profile because the failure is in the Fibre Channel/FCoE control path around VSAN, service profile, vHBA. Cisco MDS and Nexus platforms separate configuration from operational state: a VSAN, zone, vFC binding, device alias, or port-security entry can exist in configuration but still fail if it is not active, correctly merged, or allowed on the link. The correct option addresses the fabric condition that prevents communication. The incorrect options are technically adjacent but would not repair the specific dependency; for example, changing unrelated databases or resetting ports without correcting policy leaves the same failure to recur. Cisco SAN troubleshooting therefore starts with port role and VSAN checks, then confirms fabric services such as fcdomain, FSPF, zoning, fabric binding, and name-server information. The expected validation is that the port becomes operational, the initiator and target appear in the appropriate databases, and permitted zone members can communicate.

The correct remediation is Change domain ID on one pair to a different ID. In Cisco data center troubleshooting, the first priority is to isolate whether the failure is caused by the underlay, overlay control plane, first-hop gateway behavior, or a consistency parameter. This item is centered on vPC, Cisco Nexus, so the selected action targets the condition that prevents normal forwarding rather than masking the symptom. Cisco Nexus and ACI guidance treats vPC, VXLAN EVPN, OTV, OSPF, BGP, HSRP, and LACP issues as state-dependent technologies: a neighbor, peer, VLAN, VNI, multicast group, timer, MTU, or policy mismatch can leave the protocol partially operational while traffic is still dropped. The rejected alternatives either change unrelated attributes, introduce a new inconsistency, or affect only a secondary behavior. The operational check after applying the fix should be to confirm adjacency or peer state, validate the relevant route/MAC/endpoint table, and test traffic in the affected VLAN or VRF. This aligns with Cisco DCIT network troubleshooting methodology for isolating control-plane state before changing data-plane policy.

The correct answer is Change the file name. Cisco NX-OS automation features are context-sensitive: Guest Shell, Bash, EEM, scheduler, NX-API, REST calls, and Python scripts each run with their own parser, privilege model, environment, and resource limits. The scenario involves RBAC, and the selected action corrects the missing execution condition. Cisco documentation for Nexus programmability states that Guest Shell resources and networking must be configured inside the Guest Shell context, EEM applets require a valid event statement and event-default when the intercepted CLI command must continue, and API calls must target the correct managed object or class. The alternative answers either operate in the wrong context, omit a required trigger/action, or correct a parameter unrelated to the failure. Validation should include running the command manually in the same context, checking logs or return codes, and confirming that the automation completes without blocking the normal NX-OS operation it observes.

Disable the inband-telemetry feature resolves the problem because the symptom is specific to the automation subsystem handling inband-telemetry, packet postcards, Cisco Nexus, Nexus 9000, Cisco Nexus 9000. Nexus automation failures are frequently caused by a missing EEM event statement, absent event-default action, invalid REST path, incorrect JSON or XML syntax, Guest Shell DNS/resource settings, or a scheduler feature that is not enabled. The selected answer corrects that execution prerequisite. The wrong options may make sense for normal switch forwarding, but they do not repair the automation control path. Cisco documentation treats Guest Shell as a separate Linux environment and EEM as a policy engine that can intercept CLI events; both must be validated from their own operational state. A proper verification is to confirm the policy is registered, run the job or API call again, review the response or syslog output, and ensure that normal CLI behavior is preserved after the automation fires.

Cisco troubleshooting logic supports Change VMware vCenter IP address as the required fix. In this question the symptoms point to ACI, VMM, and the defect is best handled by correcting the exact control-plane or consistency condition. Nexus platforms can show interfaces or peers as configured while still refusing to forward traffic if a vPC Type-1 parameter, VLAN allowance, MTU, HSRP version, EVPN route, or routing attribute is wrong. Cisco methodology is to avoid broad resets unless the state machine is stuck; instead, correct the mismatched parameter and verify that the resulting operational state becomes stable. The other choices do not remove the root cause, or they modify a setting that is not used by the failing protocol exchange. After the change, the engineer should review the peer status, route or MAC table, and counters for drops or inconsistency messages. That sequence proves that the network fabric is fixed, not merely restarted.

The correct answer is Port 15 is configured as an Ethernet port. Cisco MDS and Nexus SAN troubleshooting is driven by fabric state: the host and target must be in the correct VSAN, must complete FLOGI/PLOGI where applicable, and must be permitted by active zoning, fcdomain, FSPF, NPV/NPIV, or port-security policy. This question focuses on UCS, fabric interconnect, so the selected action fixes the dependency that prevents the initiator, target, or inter-switch link from becoming usable. Cisco documentation emphasizes checking VSAN membership, active zonesets, correct port mode, fabric binding, device-alias consistency, and the relevant FC databases before changing unrelated server settings. The distractors either target a different database, use the wrong port role, or would not cause the observed Fibre Channel state to change. After the fix, the engineer should confirm the interface state, FLOGI database, name-server entries, zoneset activation, and successful initiator-to-target reachability with tools such as fcping or fabric show commands.

The answer is Correct the configuration of the vPC peer link and the vPC peer keepalive; Match the vPC domain ID between the two devices because Cisco Nexus and ACI forwarding depends on exact agreement between the devices participating in the feature. The scenario references vPC; those technologies fail in predictable ways when required parameters do not match or when the required control-plane advertisement is absent. In DCIT troubleshooting, the engineer should identify the failed dependency, correct that dependency, and then verify the operational table that proves the fix. For example, vPC and EVPN checks focus on consistency, VNI/VRF bindings, peer-gateway behavior, and host-route advertisement; routing checks focus on neighbor state, MTU, timers, authentication, next-hop, and route preference. The selected answer addresses the dependency that blocks forwarding. The distractors are plausible because they touch related features, but they do not resolve the specific failure condition. Post-change validation should include protocol state, learned endpoint or route entries, and a traffic test across the affected path.

The selected option, action 1.0 cli local python Config.py, is correct for the automation path described. Cisco NX-OS requires precision in EEM applets, scheduler jobs, Guest Shell operations, and REST/NX-API syntax. The affected element is EEM; therefore, the fix must be applied to the component that actually executes the action. For EEM, that means a valid event detector and explicit actions, with event-default when the matched CLI command should continue. For Guest Shell and Bash, DNS, proxy, resource allocation, and reboot behavior are local to the Linux container. For REST calls, the class name, method, authentication, and XML/JSON structure must match the APIC or NX-OS object model. The distractors usually change the switch globally or alter an unrelated command. Cisco DCIT automation troubleshooting confirms the fix by checking the returned error, then rerunning the exact job, script, or API operation in the same context.