156-315.82 Exam Dumps - Check Point Certified Security Expert R82

The correct answer isA. For Domain-Based Site-to-Site VPN routing that cannot be fully expressed through the SmartConsole VPN community options, the administrator edits the relevant vpn_route.conf file on theSecurity Management Serveror Domain Management Server, then installs policy. Check Point’s R82 Security Management Administration Guide states that the vpn_route.conf files contain the configuration for Domain-Based Site-to-Site VPN and gives the location on an R82 Security Management Server as $FWDIR/conf/vpn_route.conf. Option B is wrong for this specific question because Gaia routing controls operating-system routes, not the Check Point domain-based VPN routing table. Option C is fabricated; VTI_route.conf is not the file used. Option D is the common trap: the configuration file is managed on the Management Server side, not manually edited on each gateway in a centrally managed environment. Reference topic:Location of vpn_route.conf Files on the Management Server / Domain-Based VPN Routing.

========

The correct answer isC. In R82 Scalable Platforms and ElasticXL, the Gaia gClish commandshow cluster info interfacesshows information about cluster interfaces. Check Point’s R82 command reference states that show cluster info interfaces displays cluster interface details including name, IP address, driver name, state, throughput, and packet rate. The Scalable Platforms monitoring documentation also lists show cluster info interfaces as one of the commands used to monitor interfaces, alongside insights, asg_ifconfig, and show interfaces in Gaia gClish. Option A is not a documented ElasticXL command. Option B can show interface details in Gaia, but it is not the cluster-specific command requested by the question. Option D is a generic Linux interface command and not the R82 Scalable Platforms cluster command. The exact CCSE command to remember is:show cluster info interfaces. Reference topic:R82 Scalable Platforms CLI / show cluster info interfaces.

The correct answer isA. SmartEvent general settings and the SmartEvent Event Policy are configured through theSmartEvent GUI Client, also reached in modern deployments through SmartConsole by opening the SmartEvent Settings & Policy application. SmartView in a web browser is mainly used for viewing logs, events, reports, and dashboards, not for configuring the full SmartEvent Event Policy. SmartConsole Logs and Monitor is used for log/event visibility and navigation, but the specific configuration interface for SmartEvent settings and policy is the SmartEvent GUI/Settings & Policy client. SmartLog is a log-search and viewing tool, not the configuration interface for SmartEvent correlation behavior. For CCSE-style exam accuracy, do not choose the general log viewer; choose the specific SmartEvent configuration client.

The correct answer isDbecause Management High Availability requires a Secondary Security Management Server to act as a synchronized standby peer for the Primary Security Management Server. The purpose of Management HA is redundancy and database backup for management servers. Check Point documentation states that synchronized servers share the same management database content, including policies, rules, user definitions, network objects, and system configuration settings. A Log Server, Security Gateway, or SmartEvent Server can exist in the overall Check Point deployment, but none of them provides Management HA for the Security Management Server itself. A Security Gateway enforces policy; it does not replicate the management database. SmartEvent correlates logs and events; it does not serve as a standby Security Management Server. A Log Server stores logs but does not take over the Management Server role. Therefore, to extend a single Primary Management Server into a Management HA deployment, the required component is aSecondary Management Server. Reference topic:Installing a Secondary Security Management Server in Management High Availability.

========

The correct answer isC. In ElasticXL, theSingle Management Object, SMO, represents the ElasticXL Cluster as one managed Security Gateway object in SmartConsole. This simplifies management communication and policy installation because the administrator manages and installs policy to the ElasticXL Cluster through a single management identity rather than treating every member as a separately managed gateway. Check Point’s ElasticXL Getting Started procedure instructs administrators to configure a single Security Gateway object in SmartConsole to represent the ElasticXL Cluster and then install policy on that object. Option A is wrong because SMO does not mean automatic uncontrolled member removal; member addition and removal are managed through Gaia Portal or gClish workflows. Option B is wrong because SMO is not a dynamic IP range allocator. Option D is fabricated; SMO is not a port-assignment database. The tested feature is simple:one management object/IP path for management and policy installation. Reference topic:ElasticXL Getting Started / Single Management Object in SmartConsole.

========