156-315.82 Exam Dumps - Check Point Certified Security Expert R82

The correct answer isC. In R81 and higher, Check Point policy installation logic distinguishes betweenLegacy DumpandModern Dump. This distinction is part of the newer policy installation architecture, where some policy data can be prepared in a modern, optimized format instead of passing through the older legacy flow. Legacy Dump follows the traditional path where policy data requires verification, conversion, code generation, and compilation before being transferred to the Security Gateway. Modern Dump is the optimized path where policy data is prepared with pre-generated code and does not require the same additional compilation or verification stage before transfer. Option A is wrong because CPD and CPM are daemons/processes, not the two database dump types. Option B invents a “Monitoring Dump” category that is not part of policy installation terminology. Option D is also wrong because FWD is a gateway/logging-related daemon and AUM is not one of the database dump types. Reference topic:Policy Installation Flow / Legacy Dump and Modern Dump.

========

The correct answer is D. When a Management Server is migrated or upgraded to R82 with a changed IPv4 address, Check Point can require the special mdss.json configuration file. The documented JSON structure identifies the applicable Management Server object through the " name " field and supplies its new address through " newIpAddress4 " . Multiple server objects can be included when several Management or Log Servers change addresses. The file is named mdss.json and is placed in /var/log/ on the applicable servers. Option A incorrectly assumes both old and new IP-address fields are required. Options B and C use field names that are not part of the documented schema. This question specifically tests the JSON structure, rather than merely the conditions under which the file becomes necessary. Reference topic: Management Server Migration / Required JSON Configuration File.

The correct answer isC. During policy installation, the policy package is transferred to the Security Gateway and staged temporarily before the gateway commits the policy as the active local policy. Check Point CLI documentation identifies the installed Access Control Policy storage locations on the Security Gateway as including both the temporary policy directory and the local policy directory: $FWDIR/state/__tmp/FW1/ and $FWDIR/state/local/FW1/. The temporary directory is used during the transfer/loading stage, while the committed local policy is stored under $FWDIR/state/local/FW1/. Option A points to the temporary staging location, not the final committed policy location. Option B is wrong because $CPDIR is not the firewall policy state directory for the committed Access Control Policy. Option D is syntactically wrong because the directory is FW1, not FW-1. For exam purposes, remember the split:temporary receive/load path = _tmp; committed local policy path = local/FW1. Reference topic:Policy Installation / Access Control Policy Storage Directories.

========

The correct answer isC. During policy installation, the Management Server performs policy verification, conversion, code generation, and compilation before the policy package is transferred to the target Security Gateway. The compiled policy is prepared on theManagement Serverunder the $FWDIR/state/ < Gateway Name > /FW1 structure for the target gateway. After transfer, the Security Gateway stores installed policy files under gateway-side directories such as $FWDIR/state/__tmp/FW1/ and $FWDIR/state/local/FW1/. Option A is wrong because it places the conversion-stage compiled code on the Gateway, which is not the management-side conversion location. Option B is not the policy compilation directory. Option D is wrong because $CPDIR is not the correct policy state directory. Check Point’s policy-installation flow identifies FWM/fw_loader handling conversion, code generation, compilation, transfer, and commit; gateway-side installed policy directories are separate.

========

The correct answer isA. ElasticXL automatically configures the Sync network to192.0.2.0/24. Check Point’s R82 ElasticXL important notes state this directly. The Sync interfaces of all ElasticXL Cluster Members in the same cluster must connect to the same Layer 2 broadcast domain, usually a dedicated Layer 2 switch or VLAN. The Sync interface must not be configured as a VLAN trunk, and only one ElasticXL Cluster is supported in the same Layer 2 broadcast domain. Option B, 192.168.2.0/24, is a private RFC1918-style address but not the ElasticXL default. Option C, 192.0.0.0/24, is not the documented Sync network. Option D is also not correct. The OCR in the uploaded file mangles the address, but the official value is unambiguous:ElasticXL Sync network = 192.0.2.0/24. Reference topic:ElasticXL Important Notes / Sync network automatic configuration.

========

The correct answer isB. Before importing a Management Database on a freshly installed target Security Management Server, the administrator must ensure that the required upgrade tools are present and compatible. The R82 migration workflow uses the migrate_server utility from $FWDIR/scripts in Expert mode. The valid command form tested here ismigrate_server print_installed_tools -v < target version > . Option A is not valid syntax because it invents print --installed-tools. Option C is also not the official command form. Option D is syntactically fabricated. The reason this matters is that Advanced Upgrade depends on the target system using the correct R82 migration tools before the database import is executed. If the target system lacks the correct tools, the import can fail or produce an unsupported migration state. For CCSE R82, the clean command memory is:Expert mode → $FWDIR/scripts → migrate_server print_installed_tools -v R82 before import validation/workflow. Reference topic:R82 Management Server Migration Tool / migrate_server workflow.

========

The correct answer isAbecause Check Point Management High Availability is built around one Primary Security Management Server and one or more Secondary Security Management Servers. The R82 Security Management Administration Guide defines a Management HA environment as havingone Active Security Management Serverandone or more Standby Security Management Servers. This is the important design point: Check Point supports multiple standby peers for redundancy and database backup, but it does not support multiple Primary Management Servers as a load-sharing management design. The first server installed is the Primary; additional servers are configured as Secondary and normally operate as Standby until an administrator promotes one to Active. Option B is wrong because Management HA is not a load-sharing management-server model. Option C is too restrictive because one Secondary is not the maximum. Option D is fabricated; Management HA is not implemented by placing Primary Management Servers behind a generic load balancer. Reference topic:Management High Availability / The High Availability Environment.

========

The correct answer isA. IKEv1 Aggressive Mode performs Phase 1 negotiation usingthree packets. Check Point documentation explains that Main Mode and Aggressive Mode are IKEv1 Phase 1 modes. If Aggressive Mode is not selected, the Security Gateway uses Main Mode by default, which performs IKE negotiation with six packets. Aggressive Mode reduces this to three packets, making it faster but less protected than Main Mode. Option B is wrong because four messages is associated with the normal IKEv2 initial exchange, not IKEv1 Aggressive Mode. Option C is not a valid count for the standard aggressive exchange. Option D is the count for IKEv1 Main Mode, not Aggressive Mode. The CCSE memory rule is direct and should not be overcomplicated:IKEv1 Main Mode = 6 packets; IKEv1 Aggressive Mode = 3 packets; IKEv2 initial exchange = 4 messages. Reference topic:IPsec and IKE / Phase I Modes.

========