JN0-363 Exam Dumps - Service Provider Routing and Switching Specialist (JNCIS-SP)

The adjacency SID in segment routing is advertised by one router to inform another about the label that should be used to forward traffic to it over a particular link. In this scenario, Router B would advertise an adjacency SID to Router A, which would be usedby Router A to forward traffic to Router B. Based on the exhibit, the adjacency SID that Router B advertises to Router A would be 12.

References:

• Juniper Networks documentation on Segment Routing: Segment Routing Overview

Graceful Routing Engine Switchover (GRES) and Nonstop Active Routing (NSR) are two features used in Junos OS to provide high availability. GRES allows for the stateful failover of the Routing Engine, and NSR allows for the continuation of packet forwarding and protocol states during a Routing Engine switchover. These technologies ensure that peer nodes are not alerted during a switchover. VRRP and ISSU serve different purposes and do not apply to this specific requirement.

References:

• Juniper Networks documentation on High Availability: High Availability Features

In OSPF, a totally stubby area does not permit type 3 summary LSAs (inter-area routes) or type 5 external LSAs (routes from outside the OSPF domain) to be flooded into the area. The area border router (ABR) will only send a default route as a type 3 LSA into the totally stubby area.

References:

• Juniper Networks documentation on OSPF Areas: Understanding OSPF Areas

In IS-IS, Level 1 routes are usually contained within the same area and Level 2 routes are used to interconnect different areas. By default, routes from Level 1 are redistributed into Level 2, and vice versa, to ensure reachability between areas.

References

• Juniper Networks Technical Documentation on IS-IS

By default, IS-IS protocol leaks routing information from a Level 1 area to a Level 2 area. However, to leak routing information from a Level 2 area to a Level 1 area, an export policy must be explicitly configured.

The Segment Routing Global Block (SRGB) defines a range of MPLS labels reserved for segment routing. With an SRGB starting label of 10,000 and an index range of 500, the first usable label is indeed 10,001 because label 10,000 is typically reserved and not usedfor forwarding. The last usable label would be 10,499 because the range includes 500 labels starting from 10,001.

References:

• Juniper Networks documentation on Segment Routing: Segment Routing Overview

tunnel-end-point name {

ipv4 {

source-address 10.255.1.1;

destination-address 10.255.2.0/25;

}

gre {

key 9;

}

}

https://www.juniper.net/documentation/us/en/software/junos/routing-policy/topics/ref/statement/tunnel-end-point-edit-firewall.html

Theipandgrinterface types are used as endpoints for various tunneling protocols.ipis a generic term that can refer to any IP-based tunnel, whilegrspecifically refers to Generic Routing Encapsulation (GRE) tunnel interfaces in Junos.

References:

• Juniper Networks documentation on Interface Types: Interface Types and Their Default Properties

When deploying Link Aggregation Groups (LAGs), it is necessary for all ports in the LAG to operate at the same speed to ensure consistent performance and avoid issues with load balancing. Multi-Chassis LAG (MC-LAG) allows for the use of member links that span multiple physical devices, offering redundancy and higher bandwidth by combining the links from two separate devices into a single logical LAG.

References

• Juniper Networks Technical Documentation on Link Aggregation Groups
• Juniper Networks Technical Documentation on MC-LAG

To prevent a router from participating in the OSPF designated router (DR) and backup designated router (BDR) election process, you set the OSPF priority to 0 on the interfaces of that router. This tells OSPF that the router on those interfaces is not to be considered for election as either DR or BDR, effectively making them DRother routers. The exhibit indicates that this is the desired configuration, and therefore the correct command to issue on the Juniper device would be to set the priority to 0 on the relevant interfaces.

Junos devices learn about MAC addresses by examining the source MAC address of frames received on an interface and then storing these MAC addresses in the MAC address table (also known as the forwarding database) along with the interface on which the traffic was received.References:

• Understanding Learning and Forwarding, Juniper TechLibrary
• MAC Address Table Processing, Juniper TechLibrary

The router identifier is used by BGP and OSPF to identify the routing device from which a packet originated. The router identifier usually is the IP address of the local routing device. If you do not configure a router identifier, the IP address of the first interface to come online is used. This is usually the loopback interface. Otherwise, the first hardware interface with an IP address is used

In OSPF, if a router ID is not manually configured, Junos OS will automatically select the router ID based on the highest IP address of any of the router’s loopback interfaces. If no loopback interface exists, the highest IP address of any active interface will be used. Therefore, answer C is correct.

References:

• Juniper Networks documentation on OSPF: OSPF Overview

You can see area 0.0.0.1 set for one interface and area 0.0.0.0 for the other interface. This means the router communicates in the backbone and area 1, thus it is an ABR.

Default hello timer and dead intervals are configured

hello-interval—Specifies the length of time, in seconds, before the routing device sends a hello packet out of an interface. By default, the routing device sends hello packets every 10 seconds. The range is from 1 through 255 seconds.

dead-interval—Specifies the length of time, in seconds, that the routing device waits before declaring that a neighboring routing device is unavailable. This is an interval during which the routing device receives no hello packets from the neighbor. By default, the routing device waits 40 seconds (four times the hello interval). The range is 1 through 65,535 seconds.

https://www.juniper.net/documentation/us/en/software/junos/ospf/topics/topic-map/configuring-ospf-timers.html#:~:text=The%20hello%20interval%20and%20the,devices%20on%20a%20shared%20network .

C. The R2 device is shown as having interfaces in two different OSPF areas (Area 0 and another area not specified), which makes it an Area Border Router (ABR).D. The OSPF hello and dead intervals are set to their default values of 10 and 40 seconds, respectively.References:

• Understanding OSPF Areas and ABRs, Juniper TechLibrary
• OSPF Configuration Guide, Juniper TechLibrary

Wide metrics in IS-IS allow for a larger metric value than what is available with narrow metrics, which supports a maximum of 63. Wide metrics also enable an interface to advertise different metrics for Level 1 and Level 2, allowing for more flexible routing policies and greater scalability in large networks.References:

• IS-IS Wide Metrics, Juniper Networks Documentation
• Configuring IS-IS Wide Metrics, Juniper Networks Documentation

Theshow bgp neighborcommand in Junos OS provides a detailed description of each BGP session, including session state, options configured, and counters for messages sent and received. This is the command you would use to see a detailed list of all established BGP sessions.

References:

• Juniper Networks documentation on BGP: BGP Commands

To configure OSPFv3 (the version of OSPF that supports IPv6), you would use theset protocols ospf3command with the appropriate area and interface. OSPFv3 requires a 32-bit router ID just like OSPFv2, which is typically an IPv4 address. OSPF does not use a 128-bit router ID, so answer D is incorrect.

References:

• Juniper Networks documentation on OSPFv3: OSPFv3 Overview

By default, the router that originally sourced the route into BGP places its peer address into the attribute field. The next-hop value is then typically changed when the route is transmitted across external gGP (EBGP) links. Internal BGP (IBGP) peers do not alter the next-hop value between themselves.

B. By default, the next-hop value is changed when a route is passed from an EBGP peer to another EBGP peer.C. By default, the next-hop value is retained when a route is advertised across IBGP links.References:

• BGP Next Hop Attribute, Juniper TechLibrary
• Understanding BGP Next-Hop Selection, Juniper TechLibrary

In Ethernet switching, learning and aging are two fundamental concepts for maintaining a dynamic Ethernet switching table (also known as a MAC address table). Learning is the process by which switches listen for frames and learn the MAC addresses by associating them with the incoming port. Aging is the mechanism that ensures the switch updates its table by removing MAC addresses that have not been seen for a certain amount of time (aging time).

References:

• Juniper documentation on Ethernet switching: Understanding Ethernet Switching on Junos OS Devices

Local preference is a BGP attribute that dictates which path is preferred when multiple paths to the same destination are available. A higher local preference is preferred over a lower one. Since ISP A (AS 65501) is advertising a local preference of 100 and ISP B (AS 65502) is advertising a local preference of 200 to AS 65512, traffic from devices in AS 65512 will prefer the path via ISP B for all networks that ISP B advertises. However, since ISP A advertises the 172.20.21.0/24 network and ISP B does not, traffic for 172.20.21.0/24 will go through ISP A. For the 172.20.0.0/24 network, which both ISPs advertise, devices in AS 65512 will prefer the path via ISP B due to the higher local preference.

References:

• Juniper Networks documentation on BGP attributes: BGP Attributes and Policy

In the given exhibit, interfacege-0/0/0is configured to accept VLANs 101-120 andge-0/0/1is configured with flexible VLAN tagging, which means it can tag traffic with any VLAN ID specified. However, only VLAN 200 is explicitly mentioned forge-0/0/1.A. Traffic tagged with VLAN 101 will pass throughge-0/0/0and will egress onge-0/0/1with the same VLAN tag, because the VLAN ID is within the allowed range on both interfaces.B. VLAN 100 is not specified in the allowed VLAN range forge-0/0/0(which is 101-120),nor is it specified underge-0/0/1. Therefore, it will be dropped.References:

• Understanding VLAN Tagging, Juniper TechLibrary
• Configuring VLANs for EX Series Switches, Juniper TechLibrary

The FE80::/10 prefix is reserved for IPv6 link-local addresses. These addresses are auto-configured on all IPv6-enabled interfaces and can be used for communication within the local link (subnet) only.

References

• Juniper Networks Technical Documentation on IPv6 Addressing

A Level 1 router can become adjacent with the Level 1 and Level 1-2 (L1/L2) router. A Level 2 router can become adjacent with Level 2 or Level 1-2 (L1/L2) router. There is no adjacency between L1 only and L2 only router. HOWEVER: If two routers are in different areas, they can only form a Level 2 adjacency. As such, two routers in different areas can NOT form a Level 1 adjacency. If you want two routers to form a Level 1 adjacency, they have to be in the same area.

IS-IS (Intermediate System to Intermediate System) operates at two levels: Level 1 and Level 2. Level 1 routers are only aware of their own area's topology, while Level 2 routershave knowledge of the topology across areas. A Level 1 router cannot form an adjacency with a Level 2 router unless the Level 2 router is also operating as a Level 1 router (Level 1-2 router). Level 2 routers can form adjacencies regardless of their area IDs because Level 2 operates at the domain level and is used to interconnect different IS-IS areas.

References

• Juniper Networks Technical Documentation on IS-IS
• IS-IS Levels and Areas Explanation - Juniper Networks

https://www.juniper.net/documentation/us/en/software/junos/mpls/topics/topic-map/lsp-routers.html

In an MPLS network, the types of routers include ingress routers (where the MPLS labels are first applied), egress routers (where MPLS labels are removed), and transit routers (which switch MPLS-labeled packets through the MPLS network). Peering routers andaggregation routers are not specific types of MPLS routers; they are general network terms.

References:

• Juniper Networks documentation on MPLS: MPLS Fundamentals

For IS-IS to form adjacencies, the 'family iso' statement must be configured on the interface. This is required because IS-IS operates over the connectionless network service (CLNS) and not over IP. Without the 'family iso' configuration, IS-IS cannot form adjacencies over the interface.

References:

• Juniper Networks documentation on IS-IS: IS-IS User Guide for Routing Devices