H20-923_V1.0 Exam Dumps - HCSP-Field-Data Center Facility V1.0

NetEco is an enterprise management application with specific runtime dependencies, including supported operating system versions, database/middleware compatibility, CPU/memory/storage requirements, and network/security prerequisites. Because of these dependencies, Huawei does not treat NetEco as “hypervisor-agnostic for any virtualization platform.” In practice, NetEco deployment in virtualized environments is supported only when the virtualization stack meets Huawei’s compatibility requirements, such as validated hypervisors/virtualization solutions, proper virtual hardware settings, and resource reservation rules to ensure stable performance (especially for alarm processing, historical data storage, and northbound integration tasks). If deployed on an unverified virtualization platform, issues may occur such as clock drift, I/O latency, database performance bottlenecks, unstable NIC behavior, or unsupported VM device models, which can impact data collection, event correlation, and overall system stability. Therefore, the correct interpretation is that NetEco can be deployed onsupported/verifiedvirtualization platforms, not onanyvirtualization platform.

For the Huawei UPS5000-H, inverter startup is executed through theUPS’s own control interfaces, which provide the “Running Control / Inv. ON” operation with the required confirmations and permissions. TheUPS LCD (MDU touchscreen)supports inverter startup through menu operations such as selecting inverter start functions and confirming the action after authentication. TheUPS WebUIalso provides the same operational control path, where an operator logs in and issues theInv. ONcommand under the UPS monitoring/running control pages. These two interfaces are part of the UPS monitoring and control design and are explicitly used for commissioning and routine O&M actions.

By contrast,ECC(data center controller) andNetEco(management platform) are mainly used for site-level monitoring, alarm collection, visualization, reporting, and centralized management. While they can display UPS status and alarms (and may integrate with UPS data), inverter startup is defined as aUPS running control operationperformed on the UPS’s LCD or WebUI control plane to ensure proper authorization, safety checks, and command traceability.

For onsite replacement of a UPS power module, Huawei’s maintenance logic follows a safe “isolate → remove → insert → re-enable” sequence controlled by the moduleready switch. During removal, the ready switch must be rotated to theOFFstate first so the module is logically isolated from operation and will not participate in power conversion. After isolation, the four fixing screws are removed and a short waiting period is required to allow internal energy in capacitors to discharge before the module is pulled out. This matches statement②. During installation, the ready switch must remainOFFbefore insertion to prevent unintended startup or arcing during connector engagement. The module is placed in position, inserted slowly and evenly until fully seated, then secured with the four screws. Only after mechanical fastening and full seating is confirmed should the ready switch be rotated to theONstate to allow the system to recognize and bring the module online. This matches statement④.

After ECO mode is enabled on the UPS5000-H, the system’s control objective changes from “always supply the load through the inverter” to “maximize efficiency while keeping protection mechanisms ready.” When themains input is within the configured ECO acceptance window(voltage, frequency, THD, and other quality thresholds), the UPS supplies the critical load primarily through thestatic bypass path, which has lower conversion losses than continuous double-conversion. The inverter remains synchronized and on standby, so if the mains quality deteriorates or an abnormal condition is detected, the UPS canrapidly transferthe load back to inverter operation to maintain output stability. Battery mode is only used when the rectifier/bypass source is unavailable or out of range, and maintenance bypass is a manual service path used for isolation during maintenance, not for normal energy-saving operation. Therefore, with stable utility power and ECO configured, the UPS5000-H mainly operates instatic bypass mode.

In Huawei’s data center O&M architecture, video is treated as an important auxiliary capability for security and remote operation. TheVideo Managementfunction is designed not only to view live camera feeds, but also to integrate video resources into the same O&M workflow as alarms, access control events, and environmental monitoring. In typical deployments, the actual video storage and recording are handled by athird-party video surveillance subsystem(for example, an NVR/VMS platform). Huawei’s video management function can connect to that third-party subsystem so that camera resources can be accessed in a unified interface, allowing operators to perform linkage operations such as “view video on alarm” and routine security inspection without switching platforms. Because historical recordings are stored by the surveillance subsystem, once the integration is established and permissions are correctly configured, operators can retrieve andplay back historical videofor event tracing, audit, and incident investigation. This supports closed-loop O&M: alarm/event occurs → video verification → root-cause confirmation → maintenance action → evidence retention.

Wizard startup commissioning is designed to verify that the unit’skey controllable subsystemscan be started, regulated, and protected correctly. Conditions that prevent a subsystem from operating normally will directly cause commissioning failure. If thecondensate pump is stuck, the drainage function cannot be validated and water may accumulate in the drain pan, which is treated as a functional fault during commissioning. Ifindoor fan 2 drive is faulty, the fan system cannot meet airflow requirements or redundancy expectations, so the fan commissioning item fails. If theelectronic expansion valve (EEV) is not opened, refrigerant flow and cooling control cannot be established, so the cooling system commissioning fails because the unit cannot build a stable refrigeration cycle or reach expected operating parameters.

In contrast, thewater leakage ropeis aprotective detection accessoryused for leak sensing and alarming. While it is important for site safety and recommended for operation, its absence typically does not block the unit from completing the functional commissioning steps for fans, cooling, and drainage; it mainly affects leak detection coverage and related alarms rather than the basic startup commissioning pass/fail.

NetEco is a management platform that stores critical operational data, including site configuration, device models, user/role information, historical alarms, trend data, reports, and northbound integration settings. To protect these assets and ensure service continuity, NetEco provides a built-in backup mechanism that supports bothmanualandautomaticbackup modes.Manual backupis typically used before major operations such as version upgrades, configuration changes, northbound interface adjustments, or large-scale device onboarding, so engineers can create a restore point on demand.Automatic backupis used for routine risk control and is normally implemented through scheduled tasks, allowing backups to be generated at defined intervals to reduce data-loss exposure in case of hardware failure, system corruption, or accidental misconfiguration. In standard O&M practice, automatic backups are combined with retention policies (for example, keeping a rolling set of backup files), storage capacity checks, and periodic restore verification to confirm backup integrity. This dual-mode backup capability is a foundational requirement for stable long-term operation of management systems like NetEco.

Power Partner is Huawei Digital Power’s partner service platform used to support delivery, commissioning, maintenance, and service operations across the full lifecycle of a project. To match real project workflows, the platform defines multiple user roles that align with different responsibilities and permission scopes. AStartup engineerfocuses on commissioning activities such as obtaining startup authorization, performing initial configuration, and completing functional verification. AService engineerhandles routine maintenance, inspections, troubleshooting, part replacement guidance, and closure of service cases. AProject managercoordinates delivery milestones, resource planning, and overall service execution to ensure acceptance criteria are met. AnInventory operations managermanages materials/parts flow, tracking, and availability to support timely repair and maintenance. TheDOC (Delivery/Dispatch Operations Center)role supports centralized operations such as work order dispatching, progress supervision, and process compliance. Aservice manager of a representative officetypically oversees regional service quality, governance, and authorization control, ensuring the right people have the right access and that services are delivered according to Huawei process requirements.