300-730 Exam Dumps - Implementing Secure Solutions with Virtual Private Networks (SVPN)
Which command is used to troubleshoot an IPv6 FlexVPN spoke-to-hub connectivity failure?
Which two commands help determine why the NHRP registration process is not being completed even after the IPsec tunnel is up? (Choose two.)
Which redundancy protocol must be implemented for IPsec stateless failover to work?
Which parameter is initially used to elect the primary key server from a group of key servers?
Which method dynamically installs the network routes for remote tunnel endpoints?
Refer to the exhibit.
Cisco AnyConnect must be set up on a router to allow users to access internal servers 192.168.0.10 and 192.168.0.11. All other traffic should go out of the client's local NIC. Which command accomplishes this configuration?
Refer to the exhibit.
A customer cannot establish an IKEv2 site-to-site VPN tunnel between two Cisco ASA devices. Based on the syslog message, which action brings up the VPN tunnel?
Drag and drop the correct commands from the night onto the blanks within the code on the left to implement a design that allow for dynamic spoke-to-spoke communication. Not all comments are used.
Refer to the exhibit.
Which two tunnel types produce the show crypto ipsec sa output seen in the exhibit? (Choose two.)
A second set of traffic selectors is negotiated between two peers using IKEv2. Which IKEv2 packet will contain details of the exchange?
Refer to the exhibit.
The DMVPN tunnel is dropping randomly and no tunnel protection is configured. Which spoke configuration mitigates tunnel drops?
Which two parameters help to map a VPN session to a tunnel group without using the tunnel-group list? (Choose two.)
On a FlexVPN hub-and-spoke topology where spoke-to-spoke tunnels are not allowed, which command is needed for the hub to be able to terminate FlexVPN tunnels?
Which two changes must be made in order to migrate from DMVPN Phase 2 to Phase 3 when EIGRP is configured? (Choose two.)
An engineer would like Cisco AnyConnect users to be able to reach servers within the 10.10.0.0/16 subnet while all other traffic is sent out to the Internet. Which IPsec configuration accomplishes this task?
A network engineer must design a remote access solution to allow contractors to access internal servers. These contractors do not have permissions to install applications on their computers. Which VPN solution should be used in this design?
A network engineer must implement an SSLVPN Cisco AnyConnect solution that supports 500 concurrent users, ensures all traffic from the client passes through the ASA, and allows users to access all devices on the inside interface subnet (192.168.0.0/24). Assuming all other configuration is set up appropriately, which configuration implements this solution?
Refer to the exhibit.
An engineer is diagnosing an issue that occurred after a router at a branch site was assigned a new address. Based on the debugs, what must be done to resolve this issue?
Refer to the exhibit.
An engineer must allow Cisco AnyConnect users to access the outside interface using protocol UDP 500/4500. In addition, these clients must be able to establish an SSL connection to update Cisco AnyConnect software over the same connection. Which two actions must be taken to achieve this goal? (Choose two.)
An administrator is setting up AnyConnect for the first time for a few users. Currently, the router does not have access to a RADIUS server. Which AnyConnect protocol must be used to allow users to authenticate?
Refer to the exhibit.
An engineer has configured two new VPN tunnels to 172.18.1.1 and 172.19.1.1. However, communication between 10.1.0.10 and 10.1.11.10 does not function. Which action should be taken to resolve this issue?
Refer to the exhibit.
An IKEv2 site-to-site tunnel between an ASA and a remote peer is not building successfully. What will fix the problem based on the debug output?
A network engineer must configure the Cisco ASA so that Cisco AnyConnect clients establishing an SSL VPN connection create an additional tunnel for real-time traffic that is sensitive to packet delays. If this additional tunnel experiences any issues, it must fall back to a TLS connection. Which two Cisco AnyConnect features must be configured to accomplish this task? (Choose two.)
Which two features provide headend resiliency for Cisco AnyConnect clients? (Choose two.)
Cisco AnyConnect Secure Mobility Client has been configured to use IKEv2 for one group of users and SSL for another group. When the administrator configures a new AnyConnect release on the Cisco ASA, the IKEv2 users cannot download it automatically when they connect. What might be the problem?
Which command automatically initiates a smart tunnel when a user logs in to the WebVPN portal page?
Under which section must a bookmark or URL list be configured on a Cisco ASA to be available for clientless SSLVPN users?
Refer to the exhibit.
The customer must launch Cisco AnyConnect in the RDP machine. Which IOS configuration accomplishes this task?
Which IKE identity does an IOS/IOS-XE headend expect to receive if an IPsec Cisco AnyConnect client uses default settings?
Which requirement is needed to use local authentication for Cisco AnyConnect Secure Mobility Clients that connect to a FlexVPN server?
Refer to the exhibit.
Which two commands under the tunnel-group webvpn-attributes result in a Cisco AnyConnect user receiving the AnyConnect prompt in the exhibit? (Choose two.)
Which two statements about the Cisco ASA Clientless SSL VPN solution are true? (Choose two.)
Refer to the exhibit.
Based on the exhibit, why are users unable to access CCNP Webserver bookmark?
Which command identifies a Cisco AnyConnect profile that was uploaded to the flash of an IOS router?