New Year Sale Special Limited Time 70% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: scxmas70

200-301 Exam Dumps - Implementing and Administering Cisco Solutions (200-301 CCNA) v1.1

Searching for workable clues to ace the Cisco 200-301 Exam? You’re on the right place! ExamCert has realistic, trusted and authentic exam prep tools to help you achieve your desired credential. ExamCert’s 200-301 PDF Study Guide, Testing Engine and Exam Dumps follow a reliable exam preparation strategy, providing you the most relevant and updated study material that is crafted in an easy to learn format of questions and answers. ExamCert’s study tools aim at simplifying all complex and confusing concepts of the exam and introduce you to the real exam scenario and practice it with the help of its testing engine and real exam dumps

Go to page:
Question # 321

Refer to the exhibit.

The router has been configured with a supernet to accommodate the requirement for 380 users on a subnet The requirement already considers 30% future growth. Which configuration verifies the IP subnet on router R4?

A)

B)

C)

D)

A.

Option A

B.

Option B

C.

Option C

D.

Option D

Full Access
Question # 322

What is a requirement for nonoverlapping Wi-Fi channels?

A.

different security settings

B.

discontinuous frequency ranges

C.

different transmission speeds

D.

unique SSIDs

Full Access
Question # 323

Refer to the exhibit.

Which action must be taken to ensure that router A is elected as the DR for OSPF area 0?

A.

Configure the OSPF priority on router A with the lowest value between the three routers.

B.

Configure router B and router C as OSPF neighbors of router A.

C.

Configure the router A interfaces with the highest OSPF priority value within the area.

D.

Configure router A with a fixed OSPF router ID

Full Access
Question # 324

Which PoE mode enables powered-device detection and guarantees power when the device is detected?

A.

dynamic

B.

static

C.

active

D.

auto

Full Access
Question # 325

Refer to the exhibit.

The link between PC1 and the switch is up. but it is performing poorly. Which interface condition is causing the performance problem?

A.

There is a duplex mismatch on the interface

B.

There is an issue with the fiber on the switch interface.

C.

There is a speed mismatch on the interface.

D.

There is an interface type mismatch

Full Access
Question # 326

Refer to the exhibit.

Which command configures OSPF on the point-to-point link between routers R1 and R2?

A.

router-id 10.0.0.15

B.

neighbor 10.1.2.0 cost 180

C.

ipospf priority 100

D.

network 10.0.0.0 0.0.0.255 area 0

Full Access
Question # 327

Which action is taken by the data plane within a network device?

A.

forwards traffic to the next hop

B.

constructs a routing table based on a routing protocol

C.

provides CLI access to the network device

D.

looks up an egress interface in the forwarding information base

Full Access
Question # 328

Refer to the exhibit.

An engineer is configuring an EtherChannel using LACP between Switches 1 and 2 Which configuration must be applied so that only Switch 1 sends LACP initiation packets?

A.

Switch 1 (config-if)#channel-group 1 mode onSwrtch2(config-if)#channel-group 1 mode passive

B.

Switch1(config-if)#channel-group 1 mode passiveSwitch2(config-if)#channel-group 1 mode active

C.

Switch1{config-if)£channel-group 1 mode activeSwitch2(config-if)#channel-group 1 mode passive

D.

Switch1(config-if)#channel-group 1 mode onSwitch2(config-if)#channel-group 1 mode active

Full Access
Go to page: