Summer Sale Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: v4s65

143-085 Exam Dumps - Brocade Certified Fabric Professional Gen 5

Question # 4

You have just run SAN Health Diagnostics Capture and SAN Health Professional.

Which three critical tasks can you perform based on this report? (Choose three.)

A.

Take inventory of devices, directors, and switches.

B.

Display flows identified by Top Talkers.

C.

Display end-to-end monitor results.

D.

Capture and display historical performance data.

E.

Assess performance statistics and error conditions.

Full Access
Question # 5

You decide to implement F_Port trunking in your Gen 5 fabric.

Which two statements are true? (Choose two.)

A.

You can configure F_Port trunking between F_Ports on a Fabric OS switch and N_Ports on an Access Gateway.

B.

You can configure F_Port trunking on the F_Ports of an Access Gateway.

C.

You can configure F_Port trunking between F_Ports on a Fabric OS switch and N_Ports on a Brocade adapter.

D.

You can configure F_Ports to be E_ports with F_Port trunking on a Fabric OS switch.

Full Access
Question # 6

Which requirement must be met to enable Access Gateway mode?

A.

Ensure the switch has an Access Gateway license installed.

B.

Ensure all Ports on Demand licenses are installed.

C.

Ensure the switch is licensed for Extended Fabric.

D.

Ensure all ports are enabled.

Full Access
Question # 7

An FCIP tunnel between two Brocade 7800s is bouncing online then offline. The service provider reports that the link is experiencing errors.

What is the problem?

A.

MTU is being exceeded.

B.

Jumbo frames are being dropped.

C.

The defined link cost is being exceeded by the service provider's network.

D.

There is over commitment of the available bandwidth on the link.

Full Access
Question # 8

You have an ISL that is oversubscribed. You clear the port statistics and run the porterrshow command.

Which output would you expect to see?

A.

CRC errors incrementing with no enc_out errors

B.

enc_in errors incrementing with no CRC errors

C.

enc_out errors incrementing with no disc_c3 errors

D.

disc_c3 errors incrementing with no CRC errors

Full Access
Question # 9

Refer to the Exhibit.

As shown in the exhibit, the translate domain is not present in the FC-FC routed fabric. LSAN definitions have been confirmed.

What is the cause?

A.

Host A is member of multiple LSAN zones.

B.

Host A is not logged into the edge fabric.

C.

Storage B is logged into the backbone fabric.

D.

Host A's PWWN is a member of a TI zone.

Full Access
Question # 10

Refer to the exhibit.

You need to enable Flow Mirror for a specific frame type between an initiator and a target.

Referring to the exhibit, where would you insert the Flow Mirror?

A.

1

B.

2

C.

3

D.

4

Full Access
Question # 11

You have a server with several virtual hosts using NPIV and you want to monitor traffic from all the virtual hosts.

Which statement will satisfy this requirement?

A.

Create a bidirectional flow with the server port as the ingrport parameter and use flow learning.

B.

Create a bidirectional flow with the server port as the egrport parameter and use flow learning.

C.

Create a unidirectional flow with the server port as the ingrport parameter and use flow learning.

D.

Create a unidirectional flow with the server port as the egrport parameter and use flow learning.

Full Access
Question # 12

Which feature is used when connecting a Brocade 6510 in Access Gateway mode to different fabrics while maintaining device-to-fabric consistency?

A.

Advanced Device Security

B.

port grouping

C.

failover

D.

port mapping

Full Access
Question # 13

You need to restrict the users who are allowed to access a new Brocade DCX 8510-8. The user credentials and passwords must be centralized and identical on all DCX 8510-8s.

Which two actions will achieve this? (Choose two.)

A.

Configure LDAP authentication on all switches

B.

Configure LDAP authentication on the Principal switch

C.

Configure RADIUS authentication on the Principal switch

D.

Configure RADIUS authentication on all switches

Full Access