Summer Sale Special Limited Time 65% Discount Offer - Ends in 0d 00h 00m 00s - Coupon code: v4s65

  1. Home
  2. Cisco
  3. CCNP Enterprise
  4. 300-410 - Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)

300-410 Exam Dumps - Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)

Go to page:
Question # 4

Refer to the exhibit. The network administrator configured the branch router for IPv6 on the E 0/0 interface The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?

A.

Enable the IPv4 address family under the E 0/0 interface by using the address-family Ipv4 unicast command

B.

Disable IPv6 on the E 0/0 interface using the no ipv6 enable command

C.

Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command

D.

Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E 0/0 interface.

Full Access
Question # 5

Refer to the exhibit.

When monitoring an IPv6 access list, an engineer notices that the ACL does not have any hits and is causing unnecessary traffic to pass through the interface Which command must be configured to resolve the issue?

A.

access-class INTERNET in

B.

ipv6 traffic-filter INTERNET in

C.

ipv6 access-class INTERNET in

D.

ip access-group INTERNET in

Full Access
Question # 6

When configuring Control Plane Policing on a router to protect it from malicious traffic, an engineer observes that the configured routing protocols start flapping on

that device. Which action in the Control Plane Policy prevents this problem in a production environment while achieving the security objective?

A.

Set the conform-action and exceed-action to transmit initially to test the ACLs and transmit rates and apply the Control Plane Policy in the output direction

B.

Set the conform-action and exceed-action to transmit initially to test the ACLs and transmit rates and apply the Control Plane Policy in the input direction

C.

Set the conform-action to transmit and exceed-action to drop to test the ACLs and transmit rates and apply the Control Plane Policy m the input direction

D.

Set the conform-action to transmit and exceed-action to drop to test the ACLs and transmit rates and apply the Control Plane Policy m the output direction

Full Access
Question # 7

An engineer configured two routers connected to two different service providers using BGP with default attributes. One of the links is presenting high delay, which causes slowness in the network. Which BGP attribute must the engineer configure to avoid using the high-delay ISP link if the second ISP link is up?

A.

LOCAL_PREF

B.

MED

C.

WEIGHT

D.

AS-PATH

Full Access
Question # 8

Refer to exhibit.

Routing protocols are mutually redistributed on R3 and R1. Users report intermittent connectivity to services hosted on the 10.1.1.0/24 prefix. Significant routing update changes are noticed on R3 when the show ip route profile

command is run. How must the services be stabilized?

A.

The issue with using BGP must be resolved by using another protocol and redistributing it into EIGRP on R3

B.

The routing loop must be fixed by reducing the admin distance of iBGP from 200 to 100 on R3

C.

The routing loop must be fixed by reducing the admin distance of OSPF from 110 to 80 on R3

D.

The issue with using iBGP must be fixed by running eBGP between R3 and R4

Full Access
Go to page:

Hot Exams

ADM-201 Dumps
Platform-App-Builder Dumps
AZ-500 Dumps
350-701 Dumps
SY0-601 Dumps
NCSE-Core Dumps
PDP9 Dumps
DP-203 Dumps
AZ-700 Dumps
NSE7_EFW-7.0 Dumps
Integration-Architect Dumps
CS0-003 Dumps